Konica Minolta bizhub C35P User Manual

							Configuration Menu Overview 4-68
GLOSSY 
2Settings-8-7
Adjusts the 2nd image transfer 
output (ATVC) for duplex 
(double-sided) printing of 
glossy 2 media.
IMG 
ADJ 
THICKCYANSettings-5-0-5
Finely adjusts the density of cyan for 
images printed on thick paper.
MAGENTASettings-5-0-5
Finely adjusts the density of magenta for 
images printed on thick paper.
YELLOWSettings-5-0-5
Finely adjusts the density of yellow for 
images printed on thick paper.
BLACKSettings-5-0-5
Finely adjusts the density of black for 
images printed on thick paper.
IMG 
ADJ 
BLACKSettings-2-0-2
Finely adjusts the density of printed images for 
grayscale printing. 
FINE 
LINE 
ADJSettings-3-0-2
Adjust how fine lines are reproduced by changing 
the applied voltage (VC) to the electrostatic roller.
AIDC 
MODESettingsMODE 1 / MODE 2
Select the AIDC operation mode.
MODE1: Standard mode
MODE2: Low mode
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview4-69
THICK 
MODESettingsQUALITY MODE / SPEED MODE
In order to prevent toner from clogging within the 
developer unit as a result of it being driven at 
half-speed, select the timing for driving the devel-
oper unit at full speed for a fixed length of time when 
thick paper is being fed.
QUALITY MODE: While printing on thick paper, print-
ing is periodically paused, and the developer unit is 
driven at full speed for a fixed length of time. Since 
printing is paused, the quality is not affected; how-
ever, a standby time of approximately 70 seconds 
occurs every 400 seconds or so of half-speed oper-
ation.
SPEED MODE: While printing on thick paper, only the 
drive of the developer unit periodically switches to 
full speed for a fixed length of time. Since printing 
continues during full-speed drive, the print quality is 
slightly affected, however the standby time is short.
ENGINE 
DIPSWENGINE 
DIPSW 
1-28SettingsON / OFF
Use to change engine settings.
Normally, there is no need to change the 
settings. If it becomes necessary to change 
the settings, do so according to the 
instructions from Technical Support.
MAIN 
SCAN 
ADJUSTMAIN 
SCAN 
PAGESettingsPRINT / CANCEL
Print the test pattern for fine adjustment of the color 
ratios in the main scanning direction.
SCAN 
ADJUST 
VALUEYELLOWSettings42 - 0 - -42
Finely adjust the ratio of yellow in the 
main scanning direction.
MAGENTASettings42 - 0 - -42
Finely adjust the ratio of magenta in the 
main scanning direction.
CYANSettings42 - 0 - -42
Finely adjust the ratio of cyan in the main 
scanning direction.
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview 4-70
SUP-
PLIESRE-
PLACETRANS. 
BELTSettingsYES/NO
Resets the transfer belt counter.
TRANS. 
ROLLERSettingsYES/NO
Resets the transfer roller counter.
FUSER 
UNITSettingsYES/NO
Resets the fuser unit counter.
QUICK 
SET-
TINGUPDATE 
SETTINGSetupEXECUTE / CANCEL
Update printer settings according to the 
printer setting definition file stored in the 
USB memory device.
If EXECUTE is selected, the printer set-
tings are updated.
If CANCEL is selected, the settings are 
not updated.
BACKUP SET-
TINGBackupEXECUTE / CANCEL
Store, as a definition file, the current 
printer setting information in the USB 
memory device.
If EXECUTE is selected, the printer set-
tings are saved on a USB memory 
device.
If CANCEL is selected, the settings are 
not saved.
BACKUP TYPESettingsALL / NETWORK / PRINTER
Select the settings to be saved on a USB 
memory device.
If ALL is selected, the printer settings and 
network settings are saved on the USB 
memory device.
If NETWORK is selected, the network 
settings are saved on the USB memory 
device.
If PRINTER is selected, the printer 
settings are saved on the USB memory 
device.
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview4-71 SERVICE MENU
With this menu, the service representative can adjust the printer and perform 
maintenance operations. This menu cannot be used by the user.
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview 4-72
Downloaded From ManualsPrinter.com Manuals 
						

							Memory Direct
Downloaded From ManualsPrinter.com Manuals 
						

							Memory Direct 5-2
Memory Direct
PDF, XPS, JPEG and TIFF files saved on USB memory devices can be 
printed by plugging the USB memory device into the printer.
Memory direct can be used only if the optional hard disk kit HD-P03 or 
a CompactFlash card is installed.
Encrypted USB memory devices are not supported.
For details on specifying settings with the control panel, refer to “MEM-
ORY DIRECT” on page 4-39.
Printing From a Connected USB Memory Device
1Plug the USB memory device 
into the USB memory port.
The USB icon appears in the 
upper-right corner of the mes-
sage window, and the 
Memory 
Direct
 menu appears.
Even if SYS DEFAULT 
MENU/SECURITY/LOCK 
PANEL 
is set to ON, a pass-
word is not required for the 
menu that appears when the 
USB memory device is 
inserted.
2Select LIST OF FILES, and then press the Menu/Select key.
When all files (PDF, XPS, JPEG and TIFF) are displayed, select 
TYPE OF FILES, and then press the Menu/Select key.
3From the file list, select the file that you wish to print, and then press the 
Menu/Select key.
If the file to be printed is in a folder, select the folder, and then press the 
Menu/Select key.
A maximum of 99 folders and files can be displayed.
Up to 8 folder levels can be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							Memory Direct5-3
4Select PRINT, and then press the Menu/Select key.
When printing is finished, the status screen appears again.
Settings can be specified for the paper size, duplex printing, num-
ber of copies and collating.
Do not unplug the USB memory device from the USB memory port 
during memory direct printing.
Downloaded From ManualsPrinter.com Manuals 
						

							Memory Direct 5-4
Downloaded From ManualsPrinter.com Manuals 
						

							Using Media
Downloaded From ManualsPrinter.com Manuals