Konica Minolta bizhub C35P User Manual

							Cleaning the Printer 8-10
4Close the tray 2.
5Open the printer’s front cover.
6Remove the waste toner bottle 
and the toner cartridge and 
imaging unit for the color of laser 
lens to be cleaned.
For details on removing the 
toner cartridge, imaging unit 
or waste toner bottle, refer to 
“Replacing a Toner Car-
tridge” on page 7-5 or 
“Replacing a Imaging Unit” 
on page 7-10.
Do not tilt removed toner car-
tridge, otherwise toner may 
spill.
Do not tilt removed waste toner box, otherwise waste toner may spill.
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Printer8-11
7Attach the cover to the removed 
imaging unit.
8Insert the laser lens cleaning 
tool into the imaging unit open-
ing, pull it out, and then repeat 
this back and forth movement 2 
or 3 times.
9Install the removed toner car-
tridge, imaging unit and waste 
toner bottle.
For details on installing the 
toner cartridge, imaging unit 
or waste toner bottle, refer to 
“Replacing a Toner Car-
tridge” on page 7-5 or 
“Replacing a Imaging Unit” 
on page 7-10.
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Printer 8-12
10Close the front cover.
When closing the front 
cover, press the area of 
the cover with small pro-
jections.
11Pull out the tray 2.
12Return the laser lens cleaning 
tool to its holder on the inside of 
the tray 2.
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Printer8-13
13Close the cover.
14Close the tray 2.
15Clean between each of the laser lenses in the same way.
The laser lens cleaning tool is included with the printer.
Safely store the laser lens cleaning tool so that it will not be lost.
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Printer 8-14
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting
Downloaded From ManualsPrinter.com Manuals 
						

							Introduction 9-2
Introduction
This chapter provides information to aid you in resolving printer problems you 
may encounter, or at least guide you to the proper sources for help. 
Printing a Configuration Page
Print a configuration page to verify the printer is printing correctly, or to check 
the printer configuration.Printing the Configuration Page page 9-2
Preventing Media Misfeeds page 9-3
Understanding the Media Path page 9-4
Clearing Media Misfeeds page 9-5
Solving Problems with Media Misfeeds page 9-23
Solving Other Problems page 9-25
Solving Problems with Printing Quality page 9-30
Status, Error, and Service Messages page 9-36
Press Key 
(once)Until Display Reads
READY
PRINT MENU
If an optional hard disk kit HD-P03 is installed, the PROOF/
PRINT MENU appears at the top of the menu. Press the   
key to select the PRINT MENU.
CONFIGRATION PG
PRINT
The configuration page prints and the printer goes back
to READY.
Downloaded From ManualsPrinter.com Manuals 
						

							Preventing Media Misfeeds9-3
Preventing Media Misfeeds
Make sure that...
Media matches the printer specifications.
Media is flat, especially on the leading edge.
The printer is on a hard, flat, level surface.
You store media in a dry location away from moisture and humidity.
You always adjust the media guides in the tray after inserting the media (a 
guide that is not properly adjusted can cause poor print quality, media mis-
feeds, and printer damage).
You load the media printing-side up in the tray (many manufacturers place an 
arrow on the end of the wrapper to indicate the printing side).
Avoid...
Media that is folded, wrinkled, or excessively curled.
Double feeding (remove the media and fan the sheets—they may be sticking 
together). 
Loading more than one type/size/weight of media in a tray at the same time.
Overfilling the trays. 
Allowing the output tray to overfill (the output tray has a 200-sheet capacity—
misfeeding may occur if you allow more than 200 sheets of media to accumu-
late at one time).
Downloaded From ManualsPrinter.com Manuals 
						

							Understanding the Media Path 9-4
Understanding the Media Path
Understanding the printer’s media path will help you locate media misfeeds
1 Toner cartridge 6 Tray 3 (optional lower feeder unit 
PF-P09)
2 Output tray 7 Tray 2
3 Fuser unit FU-P02 8 Print head unit
4 Duplex 9 Imaging unit
5 Tray 1 (Manual feed tray) 10 Transfer belt unit TF-P05
321
9 10
5
4
8
7
6
Downloaded From ManualsPrinter.com Manuals 
						

							Clearing Media Misfeeds9-5
Clearing Media Misfeeds 
To avoid damage, always remove misfed media gently, without tearing it. Any 
piece of media left in the printer, whether large or small, can obstruct the 
media path and cause further misfeeds. Do not reload media that has misfed.
Note
The image is not fixed on the media before the fusing process. If you 
touch the printed surface, the toner may stick to your hands, so be 
careful not to touch the printed face when removing the misfed media. 
Make sure not to spill any toner inside the printer. 
CAUTION
Unfused toner can dirty your hands, clothes, or anything else it gets on.
If you accidentally get toner on your clothes, lightly dust them off as 
best as you can. If some toner remains on your clothes, use cool, not 
hot water, to rinse the toner off. If toner gets on your skin, wash it off 
with cool water and a mild soap.
CAUTION
If you get toner in your eyes, wash it out immediately with cool water 
and consult a doctor.
If, after clearing the media misfeed, the misfeed message in the control panel 
window persists, open and close the printer’s covers. This should clear the 
misfeed message. 
Downloaded From ManualsPrinter.com Manuals