Home > Konica > Printer > Konica Minolta bizhub C10P User Manual

Konica Minolta bizhub C10P User Manual

Here you can view all the pages of manual Konica Minolta bizhub C10P User Manual. The Konica manuals for Printer are available online for free. You can easily download all the documents as PDF.

Page 91

Replacing Consumables 79
2Pull the lever, and then open the 
top cover.
If there is paper in the 
output tray, remove it. 
Fold up the output tray 
before opening the top 
cover.
Do not touch the transfer 
belt.
3Open the front cover and check 
that the toner cartridge to be 
replaced has rotated to the 
exchange position.
PLEASE WAIT
Then, it displays OPEN  
DOOR AND/REPLACE X TONER
Press Key Until Display Reads
Downloaded From ManualsPrinter.com Manuals 

Page 92

Replacing Consumables 80
You can identify the toner cartridge by the color of the handle and 
by the letter molded into the handle: C (cyan), M (magenta), Y (yel
-
low) and K (black).
4Pull the handle on the toner car-
tridge toward you, and then pull 
the toner cartridge up to remove 
it.
Do not manually rotate 
the toner cartridge carou
-
sel. In addition, do not 
rotate the carousel with 
force; otherwise it may be 
damaged.
Note
Dispose of the empty toner cartridge according to your local...

Page 93

Replacing Consumables 81
7Remove the cover from the 
toner roller.
Do not touch or scratch 
the toner roller.
8Align the shaft on each end of 
the toner cartridge with its hold
-
ers, and then insert the car-
tridge.
Before inserting the toner 
cartridge, make sure that 
the color of the toner car
-
tridge to be installed is 
the same as the label on 
the toner cartridge carou
-
sel.
9Press down on the toner car-
tridge until it snaps into place.
Downloaded From ManualsPrinter.com Manuals 

Page 94

Replacing Consumables 82
10Close the front cover.
11Carefully close the top cover.
The printer must complete a calibration cycle (less than 2 minutes) 
after the toner cartridge has been replaced. If you open the top 
cover before the message 
IDLE appears, the printer stops and 
repeats the calibration cycle.
Downloaded From ManualsPrinter.com Manuals 

Page 95

Replacing Consumables 83
Replacing the Drum Cartridge
1Pull the lever, and then open the 
top cover.
If there is paper in the 
output tray, remove it. 
Fold up the output tray 
before opening the top 
cover.
Do not touch the transfer 
belt.
2Carefully pull out the drum car-
tridge.
Note
Dispose of the used drum cartridge according to your local 
regulations. Do not burn the drum cartridge.
Downloaded From ManualsPrinter.com Manuals 

Page 96

Replacing Consumables 84
3Prepare a new drum cartridge.
Do not touch the PC 
drum on the drum car
-
tridge.
4Install the new drum cartridge.
Downloaded From ManualsPrinter.com Manuals 

Page 97

Replacing Consumables 85
5Carefully close the top cover.
The printer must complete a calibration cycle (less than 2 minutes) 
after the drum cartridge has been replaced. If you open the top 
cover before the message 
IDLE appears, the printer stops and 
repeats the calibration cycle.
Downloaded From ManualsPrinter.com Manuals 

Page 98

Replacing Consumables 86
Replacing the Backup Battery
If the backup battery is dead, the printer’s date and time cannot be retained. 
Follow the procedure described below to replace the backup battery.
Note
It’s very important to protect the printer controller board and any 
associated circuit boards from electrostatic damage. Before performing 
this procedure, review the antistatic caution on 
Page 136. In addition, 
always handle circuit boards by the edges only.
1Turn off the printer and discon-
nect...

Page 99

Replacing Consumables 87
3Remove the rear panel.
Since there are two 
hooks on the right side of 
the panel, remove the 
rear panel by slightly pull
-
ing the left side of the 
panel toward you, then 
sliding the panel off to the 
left.
4While holding the tab on the 
hard disk mounting pin slid to the 
left, remove the hard disk.
5Remove the backup battery from 
the back of the hard disk.
Downloaded From ManualsPrinter.com Manuals 

Page 100

Replacing Consumables 88
6Install a new backup battery.
When installing the new 
backup battery, make 
sure that the + side faces 
up.
7Attach the hard disk to the 
printer controller board.
8Reinstall the panel and tighten the screw.
If you removed the duplex option in step1, reinstall it.
9Reconnect all interface cables.
Downloaded From ManualsPrinter.com Manuals 
Start reading Konica Minolta bizhub C10P User Manual

Related Manuals for Konica Minolta bizhub C10P User Manual

All Konica manuals