Konica Minolta bizhub C10P User Manual

Status, Error, and Service Messages 129
Status, Error, and Service Messages
Status, error, and service messages are displayed in the control panel mes-
sage window. They provide information about your printer and help you locate 
many problems. When the condition associated with a displayed message 
has changed, the message is cleared from the window.
Standard Status Messages
This message...means...do this...
CALIBRATINGWhenever you replace a 
toner cartridge or reboot the 
printer after making environ...

Status, Error, and Service Messages 130
Error Messages (Warning)
PROCESSINGThe printer is processing 
data.No action needed.
bizhub C10P  
STARTING SYSTEM
The printer is being started 
up.
WARMING UPThe printer is warming up.
This message...means...do this...
CANNOT ROTATE 
CARTRIDGE
A problem occurred, 
such as a media mis
-
feed, that prevents 
the toner cartridge 
carousel from rotat
-
ing.
If a media misfeed 
occurred, clear the mis
-
fed media.
DISK NEAR FULLThe optional hard disk 
is full.Delete...

Status, Error, and Service Messages 131
PAPER MISMATCHWhen using Tray 1: 
The paper size set 
from the printer driver 
is different from the 
size of paper loaded 
into Tray 1.
 
This message 
appears when 
PAPER MENU/
INPUT TRAY/
TRAY 1 MODE
 is set 
to 
AUTO and AUTO 
CONTINUE
 is set to 
OFF
.
Printing continues with 
paper of a different size, 
even if this message 
appeared.
To print using paper of 
the desired size, load 
paper of the correct size, 
and then try printing 
again.
When using Tray 2:...

Status, Error, and Service Messages 132
Error Messages (Operator Call)
This 
message...means...do this...
DISK 
ERRORThe hard disk is full or dam-
aged.
Initialize the hard disk or, if 
the error continues to occur, 
replace the hard disk.
To initialize the hard disk, 
select 
SYSTEM DEFAULT/
FORMAT/FORMAT DISK
.
DISK FULLThe hard disk is full or dam-
aged.
Initialize the hard disk.
To initialize the hard disk, 
select 
SYSTEM DEFAULT/
FORMAT/FORMAT DISK
.
DUPLEX 
UNIT
 
PANEL 
OPEN
Duplex cover is...

Status, Error, and Service Messages 133
PAPER JAM 
TRAY X
Media has misfed while being 
pulled from the specified tray 
(X).Locate and remove the mis-
feed.
PUT 
“SIZE” 
“TYPE”
 
IN TRAY 1
The paper size set from the 
printer driver is different from 
the size of paper loaded into 
Tray 1.
 
This message appears when 
PAPER MENU/INPUT 
TRAY/TRAY 1 MODE
 is set 
to 
CASSETTE.
When PAPER MENU/
INPUT TRAY/AUTO 
CONTINUE
 is set to ON: 
Printing continues with paper 
of a different size, even if this...

Status, Error, and Service Messages 134
Service Messages
These messages indicate a more serious error that can only be corrected by 
a customer service engineer. If one of these messages appears, turn the 
printer off, then turn it on again. If the problem persists, contact your local 
vendor or authorized service provider.
  
MEDIA 
MISMATCHThe media type set in the 
printer driver is different from 
the type of media loaded.Load the correct media type.
PAPER 
MISMATCHWhen using Tray 1: The paper 
size...

Installing 
Accessories
Downloaded From ManualsPrinter.com Manuals 

Introduction 136
Introduction
Note
Use of accessories not manufactured or supported by 
KONICA MINOLTA will void your warranty. 
This chapter provides information about the following accessories.
Note
Installing accessories always requires that the printer and accessories 
are turned off and unplugged during installation.
For details on the available options, refer to  
printer.konicaminolta.com.
Antistatic Protection
Note
It’s very important to protect the printer controller board from 
electrostatic...

Dual In-Line Memory Module (DIMM) 137
Dual In-Line Memory Module (DIMM)
A dual in-line memory module (or DIMM) is a compact circuit board with sur-
face-mount memory chips.
Your printer comes with 128 MB SDRAM printer memory on board. However, 
you can upgrade to a maximum of 640 MB of RAM through the installation 
 
of an additional unbuffered SDRAM DIMM. Your printer comes with one free 
DIMM slot.
Required Memory during Printing
Installing a DIMM
Note
It’s very important to protect the printer...

Dual In-Line Memory Module (DIMM) 138
2Using a screwdriver, remove the 
screw on the back of the printer.
3Remove the rear panel.
Since there are two 
hooks on the right side of 
the panel, remove the 
rear panel by slightly pull
-
ing the left side of the 
panel toward you, then 
sliding the panel off to the 
left.
4Insert the new DIMM straight 
into the DIMM connector until 
the latches snap into the locked 
position.
Observe the keyed side of the 
DIMM to align it with the connec
-
tor. If you cannot...