Konica Minolta bizhub 420 User Manual

Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-43
3Enter the desired magnification ratio (e0.250 to e4.000) from the 
control panel keypad.
Entered ratio will be displayed in the Zoom with Constant X and Y Ratio 
area.
?What should be done if the message Input Error is displayed and 
entered size is ignored?
The value just entered is out of available range.
%Press [C] (Clear) on the control panel, then reenter the correct value.
4Touch [OK].
– Touching [Cancel] will clear the magnification ratio...

4Basic Copy Operations
4-44 bizhub 500/420/360 (Phase 3)
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the Basic 
Screen.
Downloaded From ManualsPrinter.com Manuals 

Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-45To specify lengthwise and widthwise zoom ratios separately (Set 
Individual Zoom)
The following copy images can be obtained by specifying lengthwise and 
widthwise magnification ratios separately.
0Use the control panel keypad to enter the desired lengthwise/widthwise 
magnification ratio, within the range from e0.250 to e4.000 in e0.001 
increments.
0The Individual Zoom ratio cannot be registered.
0The [+] and [–] keys on the Zoom Screen cannot be...

4Basic Copy Operations
4-46 bizhub 500/420/360 (Phase 3)
1Touch [Zoom] on the Basic Screen.
The Zoom Screen will be displayed.
2Touch [XY Zoom].
The XY Zoom Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 

Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-47
3Touch the X icon key in the Set Individual Zoom area to highlight it, then 
enter the desired magnification ratio (e0.250 to e4.000) from the control 
panel keypad.
Entered ratio will be displayed on the right side of the X icon key.
?What should be done if the message Input Error is displayed and 
entered size is ignored?
The value just entered is out of available range.
%Press [C] (Clear) on the control panel, then reenter the correct value....

4Basic Copy Operations
4-48 bizhub 500/420/360 (Phase 3)
5Touch [OK].
– Touching [Cancel] will clear the Individual Zoom ratio entered on 
the XY Zoom Screen.
The Zoom Screen will be restored.
6Touch [OK].
The Basic Screen will be restored with the specified Individual Zoom 
ratio displayed on the Zoom key.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the Basic 
Screen.
Downloaded From ManualsPrinter.com...

Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-49To select a stored magnification ratio
Follow the procedure below to recall the stored magnification ratio.
0The factory default provides three types (e4.000, e2.000, e0.500) of the 
proportional zoom ratio.
0The stored ratio can be altered. For details, see To store a zoom ratio 
on page 4-51.
0Use the [+] and [–] keys on the Zoom Screen to make a fine adjustment 
on the recalled magnification ratio. Touch [+] to increase, or [–] to 
decrease the...

4Basic Copy Operations
4-50 bizhub 500/420/360 (Phase 3)
3Touch [OK].
The Basic Screen will be restored with the recalled zoom ratio 
displayed on the Zoom key.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the Basic 
Screen.
Downloaded From ManualsPrinter.com Manuals 

Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-51To store a zoom ratio
Follow the procedure below to register proportional zoom ratios to be often 
used, or to change the ratio provided as Minimal.
0Three proportional zoom ratios can be stored within the range from 
e0.250 to e4.000 in 0.001 increments. The factory default provides 
e4.000, e2.000, and e0.500 as Set Zoom ratios.
0The Minimal ratio setting can be changed within the range from e0.900 to 
e0.999. The ratio is set to e0.930 as factory...

4Basic Copy Operations
4-52 bizhub 500/420/360 (Phase 3)
3Touch the icon key in the Zoom with Constant X and Y Ratio area to 
highlight it, then enter the desired magnification ratio from the control 
panel keypad.
– When registering a proportional zoom ratio, enter the value within 
the range from e0.250 to e4.000.
– When changing the Minimal ratio setting, enter the value within the 
range from e0.900 to e0.999.
Entered ratio will be displayed in the Zoom with Constant X and Y Ratio 
area.
?What should...