Konica Minolta bizhub 420 User Manual

Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-23
4.6 Paper Setting for Bypass Tray
This section describes how to specify the size and type of copy paper loaded 
in the bypass tray.
The bypass tray is generally used in the following cases.
-Auto Detect Setting
Used as one of the trays loaded with normal paper of the size available 
for Auto Paper Select.
-Custom Size Setting
Used when loading paper of special size that cannot be loaded in other 
trays.
-Paper Type Setting
Used when loading paper...

4Basic Copy Operations
4-24 bizhub 500/420/360 (Phase 3)To automatically detect the paper size (Auto Detect)
Use this function to automatically detect the standard paper size loaded in 
the bypass tray.
0Available sizes for Auto Detect: A3 w, B4 w, A4 w/v, B5 w/v, A5 w, 
B6w, 11 e 17 w, 8-1/2 e 11 v, F4 w
0Auto Detect is initially set for the bypass tray.
1Touch [Paper] on the Basic Screen.
The Paper Screen will be displayed.
2Touch the bypass tray key to highlight it, then touch [Change Tray...

Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-25
3Touch [Auto Detect] to highlight it.
4Touch [OK] twice.
The Basic Screen will be restored.
Downloaded From ManualsPrinter.com Manuals 

4Basic Copy Operations
4-26 bizhub 500/420/360 (Phase 3)To specify/recall non-standard size (Custom Size)
Use this function to specify non-standard paper size to be loaded in bypass 
tray.
0Specify the dimensions of non-standard paper.Available range for each 
is as follows.
0Side X: 148.0 mm - 431.8 mm
0Side Y: 92.0 mm - 297.0 mm
0Five non-standard sizes can be stored and recalled. For details on storing 
non-standard size, see To store non-standard size (Custom Size) on 
page 4-29.
1Touch [Paper] on...

Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-27
3Touch [Custom Size].
The Custom Size Screen will be displayed.
4Enter the length (X) and width (Y) of the paper.
– Check that [X] is highlighted, then enter the size of side X from the 
control panel keypad. (148.0 mm - 431.8 mm)
– Touch [Y] to highlight it, then enter the size of side Y from the 
control panel keypad. (92.0 mm - 297.0 mm)
– To recall the stored non-standard size, touch one of [memory 1] to 
[memory 5]. The name displayed on the...

4Basic Copy Operations
4-28 bizhub 500/420/360 (Phase 3)
5Touch [OK] three times.
The Basic Screen will be restored with the specified paper size 
displayed on the Paper key.
2
Reminder 
Be sure to load paper of specified size in the tray, otherwise paper 
misfeed may be caused.
Downloaded From ManualsPrinter.com Manuals 

Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-29To store non-standard size (Custom Size)
Follow the procedure below to store up to five non-standard paper sizes. 
This function allows you to quickly select the non-standard size that is often 
used, dispensing with the size entry for each time.
0Specify the dimensions of non-standard paper.
0Available range for each is as follows.
0Side X: 148.0 mm - 431.8 mm
0Side Y: 92.0 mm - 297.0 mm
0To recall the stored non-standard size, see To...

4Basic Copy Operations
4-30 bizhub 500/420/360 (Phase 3)
3Touch [Custom Size].
The Custom Size Screen will be displayed.
4Enter the length (X) and width (Y) of the paper.
– Check that [X] is highlighted, then enter the size of side X from the 
control panel keypad. (148.0 mm - 431.8 mm)
– Touch [Y] to highlight it, then enter the size of side Y from the 
control panel keypad. (92.0 mm - 297.0 mm)
?What should be done if the message Input Error is displayed and 
entered value is ignored?
The value just...

Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-31
6Store the entered sizes. (The name displayed on the custom size key 
can also be changed.)
– Touch one of [memory 1] to [memory 5] to store the entered sizes.
– To change the name displayed on the key, touch [Custom Name] 
under the key to display the touch screen keypad, enter the new 
name, then touch [OK]. Up to 16 characters can be entered.
– The name on the key is not necessary to be changed.
Downloaded From ManualsPrinter.com Manuals 

4Basic Copy Operations
4-32 bizhub 500/420/360 (Phase 3)
7Touch [OK] four times.
The Basic Screen will be restored.
2
Note 
The name displayed on the stored size key is not always necessary to be 
changed.
Downloaded From ManualsPrinter.com Manuals