Konica Minolta bizhub 362 User Manual

11Utility mode
11-50 362/282/222
Utility mode
Chapter 11
11.10 Specifying software switch settings (machine func-
tions)
By specifying the software switch settings (“Mode Selection”, “Bit Selection” 
and “Hex Selection”), various machine functions can be changed to meet 
your specific needs.
2
Reminder 
Do not change any modes or bits other than those described in this man-
ual.
2
Note 
When “Enhance Security” is set to “ON”, the software switch settings 
cannot be changed.
Software SW settings...

Utility mode11
362/282/222 11-51
Utility mode
Chapter 11
To specify a software switch setting
1Enter Administrator mode, and then touch [Admin. 2].
2Touch [Software SW].
The soft SW Setting 
screen appears.
3Touch [Mode Selection], 
and then use the keypad 
to type in the mode 
number.
8 0000 1000 08
9 0000 1001 09
10 0000 1010 0A
11 0000 1011 0B
12 0000 1100 0C
13 0000 1101 0D
14 0000 1110 0E
15 0000 1111 0F
16 0001 0000 10
.
.
..
.
..
.
.
255 1111 1111 FF
Decimal number“Bit Selection” setting (bina-
ry...

11Utility mode
11-52 362/282/222
Utility mode
Chapter 11
4Touch either [Bit Selec-
tion] or [HEX Selection], 
and then specify the set-
ting.
– To specify the bits, 
touch [Bit Selection], 
touch  and 
to move the cur-
sor to the bit to be 
changed, press ei-
ther the [0] or [1] key 
in the keypad to 
specify the bit, and then touch [Enter].
– To specify the hex 
value, touch [HEX 
Selection], specify 
the value by either 
using the keypad or 
touching [A] through 
[F], and then touch 
[Enter].
5To...

Utility mode11
362/282/222 11-53
Utility mode
Chapter 11
Specifying permissions for copy functions (mode 307)
The machine can be set so that copy functions cannot be used. In this case, 
the Basics screen does not appear, even after the [Copy] key is pressed.
Settings at time of purchase
Specifying the setting
The shaded cells indicate the settings selected at the time of purchase.
Specifying the enlarged display method (mode 311)
Specify the method for displaying enlargements of screens.
Settings at...

11Utility mode
11-54 362/282/222
Utility mode
Chapter 11Specifying that the “Auto Paper Select” setting and the “Auto Zoom” 
setting can be selected at the same time (mode 403)
If a paper tray is selected while the “Auto Paper Select” setting is specified, 
the “Auto Zoom” setting can be set automatically.
Settings at time of purchase
Specifying the setting
The shaded cells indicate the settings selected at the time of purchase.
6Specify whether to 
enlarge the upper-left 
corner of the screen 
or wait...

Utility mode11
362/282/222 11-55
Utility mode
Chapter 11
Specifying the measurement units (mode 426)
Specify the units used to display and specify lengths shown in the screens.
Settings at time of purchase
Specifying the setting
The grayed out cells are the settings at the time of purchase.
Specifying settings when copying is finished using the ADF (mode 429)
Specify whether or not all settings are reset when copying is finished using 
the ADF.
Settings at time of purchase
Specifying the setting
The...

11Utility mode
11-56 362/282/222
Utility mode
Chapter 11
Specifying the pressing of the [Access] key when logging off (mode 438)
Select whether or not the [Access] key be pressed when logging off.
Settings at time of purchase
Specifying the setting
The shaded cells indicate the settings selected at the time of purchase.
Specifying use of registered user authentication information to log on to 
the LDAP server (mode 466)
Specify whether or not user names and passwords registered with user au-
thentication...

Utility mode11
362/282/222 11-57
Utility mode
Chapter 11
Specifying the setting
The shaded cells indicate the settings selected at the time of purchase.
!
Detail 
The information for the LDAP server to be connected to must be regis-
tered in order to use the LDAP server. In addition, when LDAP and user 
authentication is synchronized, select “Active Directory” as the user au-
thentication method. Select “GSS-SPNEGO” as the LDAP authentication 
method. For details on the user authentication method, refer...

11Utility mode
11-58 362/282/222
Utility mode
Chapter 11
*1 This setting is applied after the machine is turned off, then on again.
!
Detail 
If “Enhance Security” is set to “ON”, the access lock, password rules and 
overwriting of temporary data are enabled. For details on the “Enhance 
Security” parameter, refer to “Specifying security settings (Security Set-
ting parameters)” on page 11-62.
The access lock can be canceled with each password. For details, refer 
to “Canceling an access lock (“Unlock”...

Utility mode11
362/282/222 11-59
Utility mode
Chapter 11
2
Note 
If bit 6 is set to “1”, the scanning and printing speed may be reduced.
Specifying the setting for displaying a list of users in the User Authenti-
cation screen (mode 471)
Specify whether or not [User List] appears in the screen for machine authen-
tication and specify the screen that appears as a default when [User List] is 
touched.
Settings at time of purchase
Specifying the setting
The grayed out cells are the settings at the time of...