Konica Minolta bizhub 362 User Manual

11Utility mode
11-10 362/282/222
Utility mode
Chapter 11
4Select a tab, and then 
select a parameter to be 
set.
5Specify the desired settings, and then touch [Enter].
– To cancel changes to the settings, touch [Cancel].
– To exit the User’s Choice screens, touch [Enter] in each screen until 
the Basics screen appears.
Mixed Original Detection
Language Selection
2
Note 
If user authentication is performed to log onto the machine, then the dis-
play language is changed, it will no longer be possible to...

Utility mode11
362/282/222 11-11
Utility mode
Chapter 11
Measurement Unit Setting
Machine Authentication PW Change
2
Note 
This parameter appears only when the machine is being used with the 
machine user authentication settings specified.
Default Setting Simplex/Duplex
Auto Paper/Auto Zoom
TabParameterDescriptionDefault Setting
1/6 Measurement Unit 
SettingSelect one of the following as the meas-
urement units in which values are dis-
played in the touch panel.
mm (Num. Value), Inch (Num. Value), 
Inch...

11Utility mode
11-12 362/282/222
Utility mode
Chapter 11
Priority Tray
Special Paper Setting
2
Note 
If a special setting is specified for a paper tray, the icon for the special 
paper setting appears on the button for the paper tray.
!
Detail 
For details on the special paper, refer to “Special paper” on page 7-5.
Zoom Ratio for Combine/Booklets
TabParameterDescriptionDefault Setting
2/6 Priority Tray Select which of the four paper trays is 
given priority when the “Auto Paper Se-
lect” setting is not...

Utility mode11
362/282/222 11-13
Utility mode
Chapter 11
Low Power Mode
Sleep Mode
!
Detail 
If the “Disable Sleep Mode” parameter in Administrator Management is 
set to “Yes”, [OFF] appears and users can select whether or not the Sleep 
mode is disabled. For details, refer to “Disable Sleep Mode” on 
page 11-26.
LCD Back-Light OFF
Auto Reset
TabParameterDescriptionDefault setting
3/6 Low Power Mode Specify the desired length of time (be-
tween 1 and 240 minutes) until the ma-
chine enters Low Power...

11Utility mode
11-14 362/282/222
Utility mode
Chapter 11
Auto Reset when Account is changed
4in1 Copy Order
Default Quality/Density Modes
Default Copy Output Levels
TabParameterDescriptionDefault setting
3/6 Auto Reset when 
Account is 
changedSelect whether or not the settings are re-
set to their defaults when an access 
code is entered or the key counter has 
been removed.ON
TabParameterDescriptionDefault setting
4/6 4in1 Copy Order Select one of the following as the page 
order when the “4-in-1”...

Utility mode11
362/282/222 11-15
Utility mode
Chapter 11
Print Density
Default Finishing Mode
2
Note 
[Corner Staple] and [2 Staples] appear only if optional finisher is installed.
[Hole Punch] appears only if optional punch unit is installed.
Sort/Non-Sort Auto Change
!
Detail 
If the “Sort/Non-Sort Auto Change” parameter is set to “ON”, the “Uncol-
lated” setting is selected when only one page was copied, and the “Sort” 
setting is selected when two or more pages are copied....

11Utility mode
11-16 362/282/222
Utility mode
Chapter 11
Output Tray Settings
!
Detail 
If the optional output tray are installed on the finisher, the factory default 
setting for “Copy” is “3” (optional output tray).
2
Note 
The “Output Tray Settings” parameter appears only if optional finisher or 
job separator is installed.
Auto Paper Select for Small Orig.
TabParameterDescriptionDefault setting
5/6 Out-
put 
Tray 
Set-
tingsFaxes/
PrintsFax Select the output tray for data re-
ceived at the fax port.1...

Utility mode11
362/282/222 11-17
Utility mode
Chapter 11
Crease/Center Staple
2
Note 
The “Crease/Center Staple” parameter appears only if optional finisher or 
saddle stitcher is installed.
Default Screen
2
Note 
The names of parameters and settings may be different when fax kit is 
installed.
!
Detail 
The Default LCD Screen setting specifies the default screen when the au-
tomatic panel reset operation is performed or the machine is turned off, 
then on again.
In order to check the setting after it...

11Utility mode
11-18 362/282/222
Utility mode
Chapter 11
Default Device
Image Quality (ADF)
TabParameterDescriptionDefault setting
6/6 Default Device Select one of the following as the mode 
given priority.
Copy, PrinterCopy
TabParameterDescriptionDefault setting
6/6 Image Quality 
(ADF)Select one of the following as the image 
quality level for the ADF.
•Left:
Mode1 (for density correction)
For reproducing faint documents, 
such as those written in pencil
•Right:
Mode2 (standard)
For normal...

Utility mode11
362/282/222 11-19
Utility mode
Chapter 11
11.3 Specifying User Management settings
From the User Management screen, settings for more comfortable use of the 
machine can be specified, such as the volume.
The following procedure describes how to display the User Management 
screen and specify its settings.
To specify user management settings
1Press the [Utility/Counter] key.
The Utility/Counter screen appears.
2Touch [User Manage-
ment].
The User Management 
screen appears.
3Select a...