Konica Minolta bizhub 362 User Manual

9Replacing toner bottles and staples and emptying punch waste containers
9-14 362/282/222
Replacing toner bottles and staples and emptying punch waste containers
Chapter 9
9.3 Clearing a staple jam
If a staple jam occurs, the message shown below appears.
For a staple jam in the saddle stitcher:
2
Reminder 
Be careful when clearing jammed staples since injuries may result.
Follow the procedure described below to clear jammed staples. If the pa-
per is pulled out with too much force, the stapler unit may...

Replacing toner bottles and staples and emptying punch waste containers9
362/282/222 9-15
Replacing toner bottles and staples and emptying punch waste containers
Chapter 9
To clear jammed staples in finisher
1Remove all paper from 
the finisher.
2Open the front door.
3Lower lever FN1, and 
then remove any paper.
FN1
Downloaded From ManualsPrinter.com Manuals 

9Replacing toner bottles and staples and emptying punch waste containers
9-16 362/282/222
Replacing toner bottles and staples and emptying punch waste containers
Chapter 9
4Turn dial FN2.
– If the punch unit is in-
stalled, pull out the 
hole-punch waste 
container.
5Lower lever FN3, and 
then remove any paper.
6Return levers FN1 and FN3 to their original positions.
– If the punch unit is installed, insert the hole-punch waste container 
into its original position.
FN2
FN3
Downloaded From...

Replacing toner bottles and staples and emptying punch waste containers9
362/282/222 9-17
Replacing toner bottles and staples and emptying punch waste containers
Chapter 9
7Lower lever FN4.
8Turn dial FN5 or dial 
FN6, and then pull out 
any paper.
9Return lever FN4 to its original position.
10Turn the dial to the left to 
move the stapler toward 
the front.
FN4
FN6
FN5
Downloaded From ManualsPrinter.com Manuals 

9Replacing toner bottles and staples and emptying punch waste containers
9-18 362/282/222
Replacing toner bottles and staples and emptying punch waste containers
Chapter 9
11Push up the staple car-
tridge holder, and then 
remove it toward you.
12Raise the shutter of the 
staple cartridge holder, 
and then pull out one 
sheet of staples.
13Return the shutter to its original position.
14Insert the staple car-
tridge holder until it locks 
into place.
Downloaded From ManualsPrinter.com Manuals 

Replacing toner bottles and staples and emptying punch waste containers9
362/282/222 9-19
Replacing toner bottles and staples and emptying punch waste containers
Chapter 9
15Close the front door.
2
Reminder 
If stapling still cannot be resumed, even after performing the above pro-
cedure, contact your technical representative.
To clear jammed staples in the saddle stitcher
1Open the front door.
2Lower lever FN1, and 
then remove any paper.
FN1
Downloaded From ManualsPrinter.com Manuals 

9Replacing toner bottles and staples and emptying punch waste containers
9-20 362/282/222
Replacing toner bottles and staples and emptying punch waste containers
Chapter 9
3Turn dial FN2.
– If the punch unit is in-
stalled, pull out the 
hole-punch waste 
container.
4Lower lever FN3, and 
then remove any paper.
5Return levers FN1 and FN3 to their original positions.
– If the punch unit is installed, insert the hole-punch waste container 
into its original position.
FN2
FN3
Downloaded From...

Replacing toner bottles and staples and emptying punch waste containers9
362/282/222 9-21
Replacing toner bottles and staples and emptying punch waste containers
Chapter 9
6Lower lever FN4.
7Turn dial FN5 or dial 
FN6, and then pull out 
any paper.
8Return lever FN4 to its original position.
9Open the misfeed-
clearing door, and 
then pull out any mis-
fed paper.
FN4
FN6
FN5
Downloaded From ManualsPrinter.com Manuals 

9Replacing toner bottles and staples and emptying punch waste containers
9-22 362/282/222
Replacing toner bottles and staples and emptying punch waste containers
Chapter 9
10Raise the copy output 
tray, and then push 
down the staple car-
tridge holder and re-
move it.
11Raise the shutter of the 
staple cartridge holder, 
and then pull out one 
sheet of staples.
12Return the shutter to its original position.
13Insert the staple car-
tridge holder, and then 
push it up until it locks 
into place.
– When...

Replacing toner bottles and staples and emptying punch waste containers9
362/282/222 9-23
Replacing toner bottles and staples and emptying punch waste containers
Chapter 9
14Return the copy output tray to its original position.
15Close the misfeed-clearing door.
16Close the front door.
2
Reminder 
If stapling still cannot be resumed, even after performing the above pro-
cedure, contact your technical representative.
Downloaded From ManualsPrinter.com Manuals