Inter-Tel GMX-48 INSTALLATION & MAINTENANCE Manual

PROGRAMMING 
Issue 2, May 1990 ‘. 
INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
DAY SCOS INFORMATION 
(0) LIST OF UNRESTRICTED STATIONS (ALL) 
RESTRICTED 
(1) OPERATOR ACCESS 
LIST OF STATIONS (NONE): 
(2) TOLL ACCESS 
LIST OF STATIONS (NONE): 
(3) INTERNATIONAL 
LIST OF STATIONS (NONE): 
(4) EIGHT DIGIT 
LIST OF STATIONS (NONE): 
(5) AREA/OFFICE CODE 
LIST OF STATZONS (NONE): 
(6) ARS ONLY (NONE): 
LIST OF STATIONS (NONE: 
(7) ALTERNATE CARRIER 
LIST OF STATIONS (NONE): 
(8) ENABLE ALD 
LIST...

INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE ‘. 
PROGRAMMING 
Issue 2, May 1990 
B. 
[HB] OVERLAPPING AREA/OFFICE example, 901 is an area code in Tennessee and is an 
CODES (/OVER) office code in the 818 area code in the Los Angeles 
11.5 This program is used to designate whether or 
not the system is being programmed in an area where 
some of the area codes and office codes overlap. For area. This program is reached by entering B from the 
toll restriction menu or enter HB or /OVER from the...

PROGRAMMING 
Issue 2, May 1990 ‘. 
INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
C. [HC] AREA/OFFICE CODES 
ALLOWED/RESTRICTED (/AREA} 
11.6 
This program is used to specify the area codes 
and office codes to which calls are allowed or re- 
stricted for those users assigned with SCOS 5 (al- 
lowed area/office codes). It is reached by entering C 
from the toll restriction menu or HC or 
/AREA from 
the database programming menu. Refer to Figure 
5-13, page 5-163, for a program planning sheet....

INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE PROGRAMMING 
Issue 2, May 1990 
XXX (R) : 
After all area codes have been reviewed, the prompts 
continue as follows: 
REVIEW SAME AREA CODES AGAIN (N)? 
LIST OF ADDITIONAL AREA CODES TO BE 
RESTRICTED ( ): 
LIST OF ADDITIONAL AREA CODES TO BE 
ALLOWED ( ): 
REVIEW ADDITIONAL AREA CODES (N)? 
OFFICE CODES FOR AREA CODE 
[local area code] 
INITIALIZE ALL OFFICE CODES TO SAME 
ALLOWED/RESTRICTED STATUS (N)? 
INITIAL ALLOWED/RESTRICTED 
STAWS OF ALL...

PROGRAMMING 
Issue 2, May 1990 ‘. 
INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
LIST OF ADDITIONAL OFFICE CODES TO 
BE RESTRICTED ( ): 
LIST OF ADDITIONAL OFFICE CODES TO 
BE ALLOWED ( ): List of exceptions or additions to the value aSsigned 
above. ALL is a valid entry. This prompt does not 
show the current status of the office codes. 
REVIEW ADDITIONAL OFFICE CODES (N)? Y- Return to the RANGE OF OFFICE CODES 
prompt. 
N- Continue to the next prompt. 
PERFORM UPDATE TO SYSTEM DATABASE 
gr...

INTER-TEL PRACTICES ‘. 
PROGRAMMING 
GMX-48 INSTALLATION & MAINTENANCE Issue 2, May 1990 
D. [HD] AREA/OFFICE CODE REPORTS (/AREP) 
11.10 
Select D from the toll restriction menu or enter HD or /AREP from the database programming menu to 
print summary reports of area code and office code assignments. The prompts appear as shown below. End each 
entry with < CR 
> . 
REPORT OUTPUT PORT This prompt does not appear in Basic software. 
P = PRIMARY Choose the output port to which the printer will be 
A =...

PROGRAMMING 
Issue 2, May 1990 ‘. 
INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
E [HF] ALLOWED LONG DISTANCE (/ALD) 
11.14 
This program defines the allowed long dis- 
tance numbers for stations assigned with SCOS 8 (en- 
able ALD). It is reached by entering F from the toll 
restriction menu or HF or /AID from the database 
programming menu. Refer to Figure 5-13, on page 
5-164, for a program planning sheet. 
11.15 The allowed long distance numbers can have 
up to 10 digits each including the...

INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE PROGRAMMING 
Issue 2, May 1990 
12. [I] AUTOMATIC ROUTE 
SELECTION 
NOTE: This feature is available only in the Advanced 
software package. 
- 
- 
12.1 
The automatic route selection (ARS) menu is 
used to enter data for the route groups and dial rules. 
Enter I from the database programming menu to view 
the following menu: 
[I] AUTOMATIC ROUTE SELECTION 
[IA] ARS ROUTE GROUPS 
[IB] ARS DIAL RULES 0 
./ 
Dial rules: If the lines in the route groups...

PROGRAMMING 
Issue 2, May 1990 ‘.. 
INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
A. [IA] ARS ROUTE GROUPS (/ROUT) 
12.3 
This program identifies the lines and area 
codes or office codes associated with each of the route 
groups. It is reached by entering A from the auto- 
matic route selection menu or IA or /ROUT from the 
database programming menu. Refer to the program 
planning sheets (Figure 5-14, page 5-165). 
12.4 When entering an area or office code, an X can 
be included in the number...