Inter-Tel GMX-48 INSTALLATION & MAINTENANCE Manual

PROGRAMMING 
Issue 2, May 1990 INTER-TEL PRACTICES 
GMX-48 INSTALLATION Bz MAINTENANCE 
E. [E] ON-LINE ERROR REPORTS (/OLER) 
15.12 
A report of at least 20 error messages can be requested at any time using this program. Refer to the previ- 
ous page for an explanation of the types of messages. To reach this program, enter E or /OLER from the SMDR 
and error programming menu. 
ERROR OUTPUT PORT 
This prompt does not appear in Basic software. 
P = PRIMARY Choose the output port to which the error report...

INTER-TEL PRACTICES PROGRAMMING 
GMX-48 INSTALLATION & MAINTENANCE Issue 2, May 1990 
E [F] SMDR AND ERROR PASSWORD 
(/PASS) 
15.13 
This program gives the option of requiring a 
password for access to the SMDR and error program- 
ming menu. To access this program, enter F or /PASS 
from the SMDR and error programming menu. This 
password can also be programmed using the [AH] 
(passwords) program. 
15.14 If Y < CR > is entered after the REQUIRE 
PASSWORD prompt, the CHANGE and ENTER 
prompts also appear....

PROGRAMMING 
INTER-TEL PRACTICES 
Issue 2, May 1990 GMX-48 INSTALLATION & MAINTENANCE 
ENABLE AUTOMATIC SAR REPORT 
GENERATION (Y) 
: 
Y- An SAR output device is connected to the 
system. 
N- No output device is connected for SAR. 
Advance to the STATION/CO LINE DATA WAS 
LAST CLEARED prompt. 
REPORTING INTERVAL 
D = DAILY 
W = WEEKLY 
M = MONTHLY 
A = ATTENDANT 
REPORTING INTERVAL (A): D- Reports print daily. Go to the GENERATE 
DAILY REPORTS ON prompt. 
W- Reports print weekly. Go to the DAY OF 
WEEK...

I 
:.; 
:; 
INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE PROGRAMMING 
Issue 2, May 1990 
I GENERATE DAILY REPORTS ON: 
SUNDAY (Y): 
MONDAY (Y): 
TUESDAY (Y): 
WEDNESDAY (Y): 
THURSDAY (Y): 
ci FRIDAY (Y): 
3 
I’ SATURDAY (Y): 
4 
TIME-OF-DAY FOR AUTOMATIC REPORTS 
(oo:oo): 
SAR OUTPUT PORT 
P = PRIMARY 
A = ACCESSORY PORT 1 
B = ACCESSORY PORT 2 
SAR OUTPUT PORT (P) : Choose the output port to which the SAR 
recording device will be attached. Enter P for the 
KSU port or enter A or B for the...

PROGRAMMING INTER-TEL PRACTICES 
Issue 2, May 1990 GMX43 INSTALLATION & MAINTENANCE 
B. [B] ON-LINE SAR REPORTS (ISAR) 
16.6 
This program appears only in Advanced software only. This program generates an on-line SAR report. It is 
reached by entering B or /SAR from the SAR programming menu. The format settings temporarily change the 
SAR output without affecting the automatic SAR reports. The prompts appear as shown below. End each entry 
with . 
SAR OUTPUT PORT 
P = PRIMARY 
A = ACCESSORY PORT 1 
B =...

INTER-TEL PRACTICES PROGRAMMING 
GMX-48 INSTALLATION & MAINTENANCE Issue 2, May 1990 
C. [C] SAR PASSWORD (/PASS) 16.8 
If a password is created and later designated as 
not 
required, it remains in the system memory. If it is 
16.7 This program gives the option of requiring a 
password to access the SAR programming menu. It is 
accessed by entering A or /PASS from the SAR pro- 
gramming menu. This password can also be pro- 
grammed using database program [AH] (passwords) 
shown on page 5-30. later...

PROGRAMMING 
Issue 2, May 1990 INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
D. [D] CALL COST FACTORS (/COST) 
16.10 
This program establishes the variables used in 
calculating the call cost portion of the SAR and 
SMDR reports. Call cost information is also shown 
on display keysets. To access it, enter D or /COST 
from the SAR programming menu. Refer to Figure 
5-15 on page 5-167 for a program planning sheet. 
16.11 Before using this program, determine the 
daytime rates (in dollars per...

INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE PROGRAMMING 
Issue 2, May 1990 
17. CALL COST PROGRAMMING CALL COST PROGRAMMING 
NOTE: This menu appears only in the Basic software 
package. If using 
Advanced or Intermediate software, 
refer to page 5-112 for the SAR programming menu. [A] CALL COST PASSWORD 
[B] CALL COST FACTORS 
? DISPLAY MENU 
. EXIT 
17.1 Call cost programming establishes the vari- 
ables used in calculating the call cost portion of the 
SMDR reports. Call cost information is...

PROGRAMMING 
Issue 2, May 1990 INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
B. [B] CALL COST FACTORS (/COST) 
17.7 
This program establishes the variables used in 
calculating the call cost portion SMDR reports. Call 
cost information is also shown on display keysets. To 
access it, enter B or /COST from the call cost pro- 
gramming menu. Refer to Figure 5-15 on page 5-167 
for a program planning sheet. 
17.8 Before using this program, determine the day- 
time rates (in dollars per minute) for...

‘. 
INTER-TEL PRACTICES PROGRAMMING 
GMX-48 INSTALLATION & MAINTENANCE Issue 2, May 1990 
18. MENU DISPLAYS 
18.1 For convenience, the programmer can set the 
system to display menus as desired (always, at change of menu, or on request). To determine when the cur- 
rent menu is displayed, select D from the applieations 
program menu. The prompts appear as shown below. 
End each entry with < CR 
> . 
DISPLAY CURRENT MENU 
A = ALWAYS 
C = CHANGE OF MENU 
R = REQUEST ONLY 
DISPLAY CURRENT MENU 
(C)I 
A- The...