Inter-Tel Glx Plus Issue 2 Installation And Field Maintenance Manual

PROGRAMMING Issue 2, June 1993 lNTER-TEL PRACTICES 
GLX-PLUS INSTALLATION & MAINTENANCE 
4. INITIALIZE THE SYSTEM 
4.1 The KSU and APM must be initialized when it is 
first installed and may require a reset or initialization if a 
database error occurs (refer to TROUBLESHOOT- 
ING). The KSU and APM are initialized using separate 
procedures, as described below. 
A. KSU lIWlMLIZATION 
4.2 The KSU contains the system software. The sys- 
tem features are initialized with the following default 
values. Each...

INTER-TEL PRACTICES 
GLX-PLUS INSTALLATION & MAINTENANCE PROGRAMMING Issue 2, June 1993 
3, 
The initialization function returns the database to 
KSU Initialization 
4.6 The following steps give the procedures for ini- 
tializing the KSU. These steps MUSTbe performed be- 
fore further KSU programming is started. If an APM is 
installed, the APM software database and single-line 
ports also must be initialized ss described below. 
4.7 
TO INlTIAUZE THE iWJ: 
(1) EnsurethattheKSUPRGENspritchisintheON...

PROGRAMMING 
Issue 2, June 1993 INTER-TEL PRACTICES 
GLX-PLUS INSTALLATION & MAINTENANCE 
5. PROGRAM THE SYSTEM AND 
STATION FEATURES 
5.1 Some general programming procedures include 
the following: 
At keysets, programming is performed using the 
keypad and line keys while the handset is on hook. 
At single-line stations, programming is performed 
off hook after dial tone is received. 
At keyset stations, lifting and replacing the handset 
stores the programmed information and completes 
the programming...

INTER-TEL PRACTICES 
PROGRAMMING 
GLX-PLUS INSTALLATION & 
MAINTENANCE Issue 2, June 1993 
CO delay timer: When a station user wishes to 
redial a telephone number while still on the line, this 
timer inserts a delay between the time the user pres- 
ses the SPDL and * keys or the REDL key and the 
time the system dials the number. The delay ensures 
that the central office has restored dial tone before 
the number is dialed. The timer is preset to 2.5 
seconds during initialization. 
Speed-dial pause...

PROGRAMMING 
Issue 2, June 1993 INTER-TEL PRACTICES 
GLX-PLUS INSTALLATION & MAINTENANCE 
code returns the station to its normal toll re- 
striction status. 
- Option 6 - Privacy release: With privacy 
release enabled, users can directly access busy 
lines to join on-going outside calls. If desired, 
all keyset users can join one outside call. When 
a station user hangs up, only that user is discon- 
nected and any other parties remain connected. 
Multi-party calls cannot be placed on hold or...

INTER-TEL PRACTICES 
GLX-PLUS INSTALLATION & MAINTENANCE PROGRAMMING 
Issue 2, June 1993 
The DSS/BLF key 
for the station re- 
mains lit until the 
database has been 
PUBLIC NETWORK 
WMING TLUER 
10 = 71% break 
11 = 79% break 
12 = 86% break 
to toll restriction. 
FORWARD TO THE 
PUBLIC NETWORK 
forwarded to ou 
Page 5-11  

PROGRAMMING 
Issue 2, June 1993 INTER-TEL PRACTICES 
GLX-PLUS INSTALLATION % MAINTENANCE 
B. STATION FEATURES PROGRAMMING 
5.5 The following station features can be programmed 
using each station. For more information on these fea- 
tures, refer to the FEATURES section. Program entries 
as described below. Refer to page 5-8 for general pro- 
gramming information, if needed. 
l CO line restriction: Designates the CO line(s) that 
cannot be used to make outgoing calls from the sta- 
tion. Only incoming...

INTER-TEL PRACTICES 
GLX-PLUS INSTALLATION & MAINTENANCE PROGRAMMING 
Issue 2, June 1993 
Keyset Programming 
5.7 All keyset programming is done while on hook. Each keyset circuit is programmed individually using the at- 
tached keyset. The DSS/BLF key for the station remains lit until the database has been updated. Do not continue pro- 
gramming until the DSS/E3LF key is unlit. 
TO PROGRAM: 
RESTRICTED CO IJNES DIAL: THEN ENTER THIS: 
#l Press the line key(s) for the line(s) that will be restricted. For...

PROGRAMMING 
Issue 2, June 1993 INTER-TEL PRACTICES 
GLX-PLUS INSTALLATION & MAINTENANCE 
C. APM DATABASE PROGRAMMING 
5.9 The APM software has single-line specific fea- 
tures that relate only to the single-line Ports on the APM. 
Programming for these single-line port features is stored 
in the APM memory instead of the KSU system 
memory. The KSU system programming switch does 
not affect the APM database programming, therefore, 
the position of the switch (OFF or ON) will not interfere 
with any APM...

INTER-TEL PRACTICES 
GLX-PLUS INSTALLATION & MAINTENANCE PROGRAMMING 
Issue 2, June 1993 
Single-Line Hwktlash Timers 
NOTE: The Single-Line Hookflash timers must be set 
at least 0.1 seconds apart. For example, if the maximum 
timer is set for 0.4 seconds, the minimum timer must be 
0.3 or lower. 
5.19 The Single-Line Minimum Hookflash timer 
controls the minimum length of time that a single-line 
station must stay on hook for a hookflash to be recog- 
nized by the APM software. A hookflash shorter than...