Inter-Tel 824 Installation And Field Maintenance Manual

INTER-TEL PRACTICES 
SYSTEM PROGRAMMING 
824 INSTALLATION C MAINTENANCE 
Issue 1, June 1984 
SYSTEM PROGRAMMING 
CONTENTS 
PAGE 
1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
4-l 
2. PROGRAMMING METHODS 
..................................... 4-2 
A. PROGRAMMING TERMINAL 
................................. 4-2 
B. MAINTENANCE PANEL 
.................................... 4-3 
3. 
SYSTEM PROGRAMMING ...................................... 4-5 
A....

INTER-TEL PRACTICES 
824 INSTALLATION & MAINTENANCE SYSTEM PROGRAMMING 
Issue 1, June 1984 
.- 
..: 
2. PROGRAMMING METHODS 
A- 
PROGRAMXING TERMINAL 
2.01 Some of the data base information is programmed on-site, 
using an input/output device 
such as a CRT or printer terminal 
with a keyboard. 
The terminal is connected to the Main Distri- 
bution Frame (MDF) PCB and must have these characteristics: 
(1) RS232C compatible. 
(2) Formatted for serial ASCII with no parity. 
(3) Full-duplex transmission at...

INTER-TEL PRACTICES 
824 INSTALLATION 6r MAINTENANCE SYSTEM PROGRAMMING 
Issue 1, 
June 1984 
.B. MAINTENANCE PANEL 
2.03 
used Switches on the Maintenance Panel of the CPU pCB are also 
to program the data base. 
The switch functions are: 
l Data Write 
l System Mode Data Set 
0 Initialize 
2.04 
The Light-Emitting Diodes (LEDS) on the Maintenance Panel 
are controlled by the Function 
switches below them. 
These 
switches are used to select the program numbers and data codes. 
Where there are two...

INTER-TEL PRACTICES 
824 INSTALLATION 6r MAINTENANCE SYSTEM PROGRAMMING 
Issue 1, 
June 1984 
FIGURE 4-1. 
CPU MAINTENANCE PANEL 
Dota Wrltr Srltch 
,,S”. Mod. Switch 
Inltiollrr Srltch 
( non-lock ) 
Data Write switch: This switch is placed in the ENABLE position 
to allow data to be entered into the system memory. 
It must be 
enabled for both terminal and maintenance panel programming. 
When in the DISABLE position, 
data changes will not be recorded 
in the memory. 
System Mode switch: 
This switch...

INTER-TEL PRACTICES 
SYSTEM PROGRAMMING 
824 IBSTALLATION C MAINTEbTANCE 
Issue 1, June 1984 
3. SYSTEM PROGRAMMING .;j 
A. INITIAL PROGRAMMING OUTLINE 
3.01 Below is an outline of the suggested steps to follow to 
initially program the system. 
throughout this section. Procedures for each step are given 
(1) Set the Data Write switch on the CPU PCB in the ENABLE 
position to program the data base. 
(2) Initialize the system using the Initializeswitch. 
(3) Place the System Mode switch on the CPU PCB in...

INTER-TEL PRACTICES SYSTEM PROGRAMMING 
824 INSTALLATION & MAINTENANCE Issue 1, 
June 1984 
C. SYSTEM INITIALIZATION 
3.03 This routine initializes the system data base. It con- 
figures the software as follows: 
0 All lines are equipped and set for DTMF signalling. 
l All lines ring in to intercom number 1. 
l The system speed-dial number entry station is intercom 
number 1. 
l All outgoing calls are recorded on the Station Message 
Detail Recording (SMDR) printout. 
l Transfer Recall Time is set to 60...

INTER-TEL PRACTICES 
SYSTEM PROGRAMMING 
824 INSTALLATION & MAINTENANCE Issue 1, June 1984 
3.04 To initialize the system data base: 
(1) Ensure that the System Mode switch is in the OPERATION 
position. This procedure will drop all calls in pro- 
gress. 
(2) Place the Data Write switch in the ENABLE position. 
(3) While pressing the Initialize switch, place the System 
Mode switch in the DATA SET position. 
After the program 
.. 
number appears, 
place the System Mode switch back in the 
OPERATION...

INTER-TEL PRACTICES 
SYSTEM PROGRAMMING 
824 INSTALLATION b MAINTENANCE Issue 1, 
June 1984 
FIGURE 4-2. 
FUNCTION SWITCH PROGRAMMING 
rogram 
Name c-0. 
Intercom Data LED 
Initialized 
Line 
Number A 
B. 
0 C.O. Line 1-8 -- 
Line 0 _ Dp : 
All lines 
Equipped 
DTMF/Dial Pulse equipped 1 - DTMF 
equipped 
0 - no 
ye& .: and DTMF 
l- 
1 C.O. Line Type o-a -- 
0 - C.O. 
Bookfla‘sh 
All lines 
1 - PBX 0 - no 
independent 
l- 
yes C.O. - no 
hookflash 
2 Incoming Ring o-a -- -- 
0 - low 
All lines 
Tone 1 
-...

.INTER-TEL PRACTICES 
SYSTEM PROGRAMMING 
824 INSTALLATION & MAINTENANCE 
Issue 1, 
June 1984 
FIGURE 4-2. 
FUNCTION SWITCH PROGRAMMING (CONTD) 
?rogralTl 
1 Name c-0. Intercom 
Data LED 
Initialized 
Line Number 
A 
B 
CO Year -- -- 00-99 -- 
il Month -- -- 01-12 -- 
C2 Day -- -- 
01-31 -- 
C3 Day of Week -- 
-- 0 Mon  - -- 
1 - Tues 
2 - Wed 
3 - Thurs 
4 - Fri 
5 - Sat 
6 -Sun 
$4 Hour -- -- 
00-23 -- 
L5 Minute -- -- 
00-59 -- 
j0 Clear System 
Speed-Dial 
Numbers -- 
-- -- Data Clear -- 
0 - no 
l-...