Inter-Tel 824 Installation And Field Maintenance Manual

INTER-TEL PRACTICES SYSTEM PROGRAMMING- 
824 INSTALLATION b MAINTENANCE Issue 1, June 1984 
. 
.! 
(8) CLASS 1 AREA CODE 
1= 
This determines the allowed area codes for Toll Class B. 
No area codes are preset during initialization. 
a. Enter a three-digit area code. 
One or two digits may 
be entered, allowing any digit to be dialed. For ex- 
ample entering 9 allows calls to all area codes 900 
through 999, or entering 91 allows calls to area 
codes 910 through 919. 
1. If  is entered after the area...

INTER-TEL PtiCTICES 
SYSTEM PROGRAMMING 
824 INSTALLATION b MAINTENANCE 
Issue 1, 
June 1984 
Message Registration (10) 
3.16 This program allows you to enter up to 20 filed messages 
available to station users. 
To change the initialized messages: 
(1) Enter lO. 
The terminal will respond with a list of 
the first five current or initialized messages. 
The 
first four cannot be changed. 
(2) To change or review any message 5-20, enter a new message 
up to 16 characters long. 
a. 
If  is entered after...

INTER-TEL PRACTICES SYSTEM PROGRAMMING 
824 INSTALLATION & MAINTENANCE Issue 1, June 1984 
End (11) 
3.18 To leave the programmingmode and allow the 
Detail Recording (SMDR) printout to continue: 
(1) 
(2) 
Enter ll. The terminal will respond: 
ONLINE END 
After two minutes, 
any SMDR information 
buffered during the programming mode will which has been 
print. 
NOTE : If the END program is not used, 
the system will 
time out two minutes after the last entry, and the END 
message will display. 
Any...

INTER-TEL PRACTICES SYSTEM PROGRAMMING 
824 INSTALLATION h MAINTENANCE Issue 1, 
June 1984 
FIGURE 4-3. PROGRAMMING TERMINAL PROGRAM PLANNING SHEET 
TOLL RESTRICTION (8): 
WATS LINE(S) = 
l+DIAL= Y or N 
411 ALLOWED CLASS= A=0 B=l 
C=2 D=3 
SCC LOCAL NUMBER= 
CLASS B AREA CODES= (up to 30) 
I I I I 
I I 
------- I I I I 
--- 
I # I I 
I 8 
I I I 
---------- I 
I 
I , t 
I , 
, 
p----p-- I , 
-- 
NAME REGISTRATION (9): (up to 24 names, six characters each) 
Intercom Name Intercom 
Name 
Intercom Name 
1 9...

INTER-TEL PRACTICES SYSTEM PROGRAMMING 
824 INSTALLATION h MAINTENANCE Issue 1, 
June 1984 
FIGURE 4-4. FUNCTION SWITCH PROGRAM PLANNING SHEET. 
c-0. LINES: (check features to be programmed) 
Line Program #lo Program ill 
Program #12 
Program P13 
# 
Epuip 
1 
2 
3 
4 : .--- 
5 
6 
7 
8 C.O./PBX 
Hookfl ash Ring Tone 
-FAX 
. 
%YSTEM FEATURES:  
Program 
Number Feature 
14 CES RING ID - Y=l or N=O 
.15 PBX ACCESS CODE (O-9) - _! 
.I-. , ., ).. ., j 
:. -../ -, --...~ 
, 
50 SYSTEM SPEED-DIAL CLEAR-- yki...

INTER-TEL PRACTICES 
824 JXSTALLATION 6c MAINTENANCE SYSTEM PROGRAMMING 
Issue 1, June 1984 
FIGURE 4-4. 
EUTK!TION SWITCH PROGRAM PLANNING SHEET (CONTD) 
Program Number 20 - 
Intercom Number Assignments (20): 
Write in the 
intercom number for each circuit. 
1.1 
i:; 
1.4 
1.5 
1.6 
1.7 
1.8 2.1 
22:: 
2.4 
2.5 
2.6 
2.7 
2.8 3.1 
3.2 
3.3 
3.4 
3.5 
3.6 
3.7 
3.8 
-. 
STATION FEATURES: 
Write in the intercom number(s) to be. enabled for each feature or 00 
for all intercom numbers, 
if allowed...

INTER-TEL PRACTICES SYSTEM PROGRAMMING 
824 IXSTALLATION & MAINTENANCE Issue 1, June 1984 
. . 
FIGURE 4-4- FUNCTION SWITCH PROGRAM PLANNING SHEET (CONTD) 
Program 
Number Feature Intercom 
Number(s) 
32 Incoming C.O.: Flash - 
Line 1 
Line 2 
Line 3 
Line 4 
Line 5 
Line 6 
Line 7 
Line 8 
All Lines 0 * 
* 
* 
* 
* 
* 
* 
* 
* 
Tone - 
Line 1 
Line 2 
Line 3 
Line 4 
Line 5 
Line 6 
Line 7 
Line 8 
All Lines 0 
* 
* 
* 
* 
* 
* 
* 
* 
STATION PROGRAMMING SUMMARY 
(copy and fill out for each station)...

INTER-TEL PRACTICES 
824 INSTALLATION & MAINTENANCE SYSTEM PROGRAMMING 
Issue 1, 
June 1984 
FIGURE 4-5. 
TOLL RESTRICTION TABLE. 
P 
EOFCALL 
CW(XXX) xxx-xxxx 
Cl1 xxx-xxxx . 
900 Toll Call 
Cl1 (900) xxx-xxxx 
Toll Free Call 
Cl1 (800) xxx-xxxx 
Local Information 
Cl1 411 
Long Distance Information 
Cl1 555-xxxx 
Cl1 (xxx) 555-xXxX 
I 
Emergency 
Cl1 911 
: 
Local Call CLASSA CLASSB CLASSC CLASSD 
I 
*****Optional for all classes***** 
Matched 
*If allowed C.O. 
line for station* 
. 
Page 4-28  

INTER-TEL PRACTICES 
DIAGNOSTIC PROGRAMMING 
824 INSTALLATION & MAINTENANCE 
Issue 1, June 1984 
DIAGNOSTIC PROGRAMMING 
CONTENTS 
PAGE 
1. INTRODUCTION ............................................. 
5-l 
2. KEYSET (KTS) MONITOR (4) ................................. 
5-2 ., 
3. STATION (STN) MONITOR (5) ................................. 5-2 ... 
4. C-0. MONITOR (6) ......................................... 
5-3 
5. STATION SET-UP DATA (7) .................................. 
5-4 
1. 
INTRODUCTION 
:...

INTER-TEL PRACTICES 
824 INSTALLATION & MAINTENANCE 
. DIAGNOSTIC PROGRAMMING 
Issue 1, 
June 1984 
) 
2. KEYSET (KTS) ~0NrroR (4) 
2;Ol Thi s program allows 
you to monitor a keysets activity. 
The printout will contain ASCII characters which can be decoded 
using Figure 5-l on page 5-5. 
To monitor a keyset: 
(1) Enter 4. The terminal will respond: 
KTS MONITOR 
ENTER CKT NO.(l-24)?= 
(2) Enter the circuit number (l-24) of the keyset to be 
monitored and