Inter-Tel 824 Installation And Field Maintenance Manual

INTER-TEL PRACTICES STATION FEATURES 
824 INSTALLATION & MAIRTENAMCE Issue 1, June 1984 
.,- 
(4) Dial th e memory location code for the SCC -security code 
as in Step 2. 
, 
(5) Dial th e long distance number desired, using one of two 
methods: 
a. If speed dialing, enter the memory location code. 
OR, b. If manually dialing, press the pound (#) key: then 
dial the area code and telephone number. 
Last Humber Redial 
4.47 This feature remembers the last phone number dialed on the 
keyset. If a number...

e 
INTER-TEL PRACTICES 
824 INSTALLATION & MAINTENANCE STATION FEATURES 
-Issue 1, June 1984 
4.52 To place a call on hold while on an outside call: 
(1) Press the HOLD key. The call will be on System.Hold or 
I-Hold, depending on your keysets programming. 
OR, (2) If your keyset is programmed forsystem Hold and you wish 
to put the call on I-Hold, press your DSS key. 
(3) You will hear the intercom dial tone and the line key on 
your keyset will have a medium flutter. For other key- 
sets, if the call...

INTER-TEL PRACTICES STATION FEATURES 
824 INSTALLATION & MAINTEHA?.KE Issue 1, 
June 1984 
4.58 If the station is busy, you may reconnect with the calling 
party and notify them that the line is busy. 
The calling party 
may choose to call back, to leave a message, or to be camped-on. i 
._ 
4.59 To reconnect with a transferred call: 
If the receiving 
station does not answer, refuses the call being transferred, or 
is busy, press the medium fluttering 
line key to speak to the 
calling party. 
4.60 To...

INTER-TEL PRACTICES 
STATION FEATURES 
824 INSTALLATION h MAINTENANCE 
.Issue 1, June 1984 
c 
6. REVERSE TRAHSl?l+ 
4.65 This feature allows the station user to pick up a call 
which is holding (I-HOLD) or was transferred and is ringing at 
another station. 
Intercom calls in the same paging zone as well 
as outside calls may be reverse transferred. 
4.66 
TO pick-up a call on I-hold at another station: 
(1) Lift th e handset and press 
the DSS key of the station 
where the call has been transferred or...

INTER-TEL PRACTICES STATION FEATURES 
824 INSTALLATION b MAIrJTENANCE Issue 1, June 1984 
-> 
,I 
Two Inside Parties and One Outside Party 
4.70 This feature allows a station user to initiate a conference 
with another inside station and an outside party. The initiating 
station has control of the conference and has the option to pass 
control to the other inside station. 
4.71 To initiate a conference: 
(1) 
(2) 
(3) While on an outside call, press the.CNF key. 
The line 
key will medium flutter. 
Press...

INTER-TEL PRACTICES STATION FEATURE3 
824 INSTALLATION & MAINTENANCE Issue 1, June 1984 
4.76 To end the conference: The conference is terminated and 
the outside calls are disconnected when the controlling party 
hangs up. The conference cannot be re-entered. To reconnect the 
parties, repeat the conference call procedure. 
I. 
C-0. CALL WAITING 
4.77 This feature allows an outside call to be 
“camped-on” to a 
busy station. The busy station is alerted by the slow flashing 
line key and a double tone....

INTER-TEL PRACTICES 
824 INSTALLATION 6 MAINTEFW!K!E STATION FEATURES 
Issue 1, June 1984 
., 
‘1, 
.j 
5. 
SPECIAL STATIOH FEATURES , . . . 
5.01 This section includes the follow&g special features: 
A. Call Forwarding 
B. Do-Not-Disturb 
C. Paging Features 
D. Long Speech Warning 
E. Selectable Ring (Night Answer) 
F. Door-Mate 
A. CALL FORWARDING 
5.02 This feature enables you to temporarily transfer intercom 
-and outside calls to another station. 
calls forwarded to the same,station. Several...

INTER-TEL PRACTICES 
STATION FEATURES 
824 INSTALLATION & MAINT-CE 
Issue 1, 
June 1984 
B. DO-KXFDISTURB 
5.06 This feature allows you to block all 
your station, but still allows outgoing calls calls and pages to 
to be placed. 
5.07 To place a station in Do-Not-Disturb mode: 
(1) Lizi the h an set and press the MEM key. ,Display keysets  d 
PROGRAM MODE. 
(2) ,Press the asterisk (*I key. Display keysets show DO NOT 
DISTURB. 
(3) Press the MEM key and hang up. 
The MEM key will double 
flash, 
then...

INTER-TEL PRACTICES STATION FEATURES 
824 INSTALLATION L MAINT~CE Issue 1, 
June 1984 
5.13 
TO page the All-Call zone: 
(1) Lift the handset and press the 
PAGE key. 
(2) Press the digit 0 on the keypad.  - 
(3) When you hear the double tone, 
you have 30 seconds to 
make your announcement. 
5.14 To page an internal zone: 
(1) Lift the handset and press the PAGE key. 
(2) Press the zone code (1, 2, or 3) on the keypad. 
(3) When you hear the double tone, you have 30 seconds to 
make your announcement....

INTER-TEL PRACTICES STATION FEATURES 
824 INSTALLATION b MAINTENANCE ,Issue 1, June 1984 
(, 
E. SELECTABLE RING (NIGHT ~~3~33~1 
5.19 Using Maintenance Panel Program 21, stations can be pro- 
grammed for Selectable Ring (Night Answer), which allows the user 
to turn ringing on or off for all C.O. lines at their discretion. 
5.20 
TO set proqrammed keyset to ring: 
(1) Lift the handset and press the MEM key. Display keysets 
shows PROGRAM MODE. 
(2) Press the pound (#) key. 
NIGHT ANSWER appears on a...