InFocus Projector IN5132 User Manual

37
Operating
PbyP (Picture by Picture)  
PbyP is a function for displaying two different picture signals on a screen that is 
split into main and sub areas for each signal. 
The setting information will appear for several 
seconds when the PbyP function starts. The input 
information for each area will be displayed. A blue 
frame around the main area and an audio mark 
indicating the audio output will also be displayed. 
The information can be redisplayed with the ◄/► 
buttons after it has been erased....

38
Operating
PbyP (Picture by Picture)  (continued)
Press any button to select an input port on the remote control or press the 
INPUT button on the control panel. A dialog box to select the input signal for 
the main area will be displayed. Choose a signal using the ▲/▼ buttons. To 
change the signal in the sub area, use the ◄/► buttons to temporarily switch 
to the sub area.
You cannot display the same signal on both areas. The table below provides 
details on available input signal combinations. Any...

39
Operating
1.To start the MENU, press the MENU button. EASY MENU will appear just 
after the projector is powered on, otherwise the MENU you last used (EASY 
or ADVANCED) will appear
Using the menu function
2.(1)  Use the ▲/▼ cursor buttons to select an item 
to operate. If you want to make changes in the 
ADVANCED MENU, select the ADVANCED MENU.
(2)  Use the ◄/► cursor buttons to operate the item.
This projector has the following menus:  
PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK,...

40
Operating
Using the menu function (continued)
3.To close the MENU, press the MENU button again or select EXIT and press 
the ◄ cursor button or the ENTER button. Even if you do not do anything, the 
dialog will automatically disappear after about 30 seconds.
Indication in OSD (On Screen Display)
The general OSD meanings are described below:
IndicationMeaning
EXITSelecting this word closes the OSD menu. It's the same as 
pressing the MENU button.
RETURNSelecting this word returns the menu to the...

41
Operating
Using the menu function (continued)
Containing items of  each menu
The items contained in the menus are as per below;
MenuItems
EASY MENU (42)
ASPECT, AUTO KEYSTONE,  KEYSTONE,  KEYSTONE, 
PERFECT FIT, PICTURE MODE, ECO MODE, INSTALLATION, 
RESET, FILTER TIME, LANGUAGE, ADVANCED MENU, EXIT
PICTURE (44)BRIGHTNESS, CONTRAST, GAMMA, COLOR TEMP, COLOR, 
TINT, SHARPNESS, ACTIVE IRIS, MY MEMORY
IMAGE (47)ASPECT, OVER SCAN, V POSITION, H POSITION, H PHASE,  
H SIZE, AUTO ADJUST EXECUTE
INPUT...

42
EASY MENU
EASY MENU
From the EASY MENU, you can perform the items 
shown in the table below.
Select an item using the ▲/▼ cursor buttons. Then 
follow the instructions below.
ItemDescription
ASPECTUsing the ◄/► buttons switches the aspect ratio mode.See the ASPECT item in IMAGE menu (47).
AUTO KEYSTONE Using the ► button performs the auto keystone function.See the AUTO KEYSTONE item in SETUP menu (54).
 KEYSTONEUsing the ◄/► buttons corrects the vertical keystone distortion.
See the  KEYSTONE item...

43
EASY MENU
ItemDescription
PICTURE MODE (continued)
GAMMACOLOR TEMP
NORMAL 1 DEFAULT 2 MID
CINEMA 2 DEFAULT 3 LOW
DYNAMIC 3 DEFAULT 1 HIGH
BOARD(BLACK) 4 DEFAULT 4 Hi-BRIGHT-1
BOARD(GREEN) 4 DEFAULT 5 Hi-BRIGHT-2
WHITEBOARD 5 DEFAULT 2 MID
DAYTIME 6 DEFAULT 6 Hi-BRIGHT-3
DICOM SIM. 7 DEFAULT 2 MID
• When the combination of GAMMA and COLOR TEMP differs from the pre-assigned modes above, the display on the menu for the PICTURE MODE is “CUSTOM”. Refer to the GAMMA and COLOR TEMP (44, 45) items in PICTURE...

44
PICTURE menu
PICTURE menu
From the PICTURE menu, you can perform the items 
shown in the table below. 
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or the ENTER button to 
perform this item. Then follow the instructions below.
ItemDescription
BRIGHTNESSUsing the ◄/► buttons adjusts brightness.
Dark ó Light
CONTRASTUsing the ◄/► buttons adjusts contrast.
Weak ó Strong
GAMMA
Using the ▲/▼ buttons switches the gamma mode.
To adjust CUSTOM
Selecting a CUSTOM mode and then...

45
PICTURE menu
ItemDescription
COLOR TEMP
Using the ▲/▼ buttons switches the color temperature mode.
To adjust CUSTOM
Selecting a CUSTOM mode and then pressing the ► button or the ENTER button displays a dialog to aid you in adjusting the OFFSET and GAIN of the selected mode.OFFSET adjustments change the color intensity on the whole tones of the test pattern. GAIN adjustments mainly affect color intensity on the brighter tones of the test pattern.Choose an item using the ◄/► buttons, and adjust the...

46
PICTURE menu
ItemDescription
SHARPNESS
Using the ◄/► buttons adjusts the sharpness.
Weak ó Strong
• There may be some noise and/or the screen may flicker for a moment when an adjustment is made. This is not a malfunction.
ACTIVE IRIS
Using the ▲/▼ cursor buttons changes the active iris control mode.
PRESENTATION  ó  THEATER  ó  OFF              
PRESENTATION :  The active iris displays the best presentation image for both bright and dark scenes.THEATER :  The active iris displays the best theater...