InFocus Projector IN5132 User Manual

17
Remote control
Installing the batteries
Insert batteries into the remote control before using it (batteries not included). If 
the remote control starts to malfunction, try replacing the batteries. If the remote 
control will not be used for a long period, remove the batteries from the remote 
control and store them in a safe place.
1.Holding the hook part of the battery 
cover, remove it.
2.Align and insert two AA batteries (HITACHI 
MAXELL or HITACHI MAXELL ENERGY, 
Part No.LR6 or R6P - not...

18
30°3m30°
30°30°3m
(approx.)
About the remote control signal
The remote control works with the 
projector’s remote sensors. This 
projector has two remote sensors on the 
front and back sides.
The sensors can sense signals within 
the following range:
60 degrees (30 degrees to the left and right of the 
sensor) within approximately 3 meters.
• You can deactivate one of the sensors using the REMOTE RECEIV. 
item in the SERVICE menu of the OPTION menu (71).
• The remote control signal may be able to be...

19
Simple PC mouse & keyboard control
When the projector’s USB TYPE B port and the 
computer’s type A USB port are connected and 
MOUSE is selected for the USB TYPE B item in the 
OPTION menu (67), the remote control will work 
like a simple PC mouse and keyboard.
(1) PAGE UP key: Press the PAGE UP button.
(2) PAGE DOWN key: Press the PAGE DOWN button.
(3) Mouse left button: Press the ENTER button.
(4) Move pointer:  Use the cursor buttons  
▲, ▼, ◄ and ►.
(5) ESC key: Press the ESC button.
(6) Mouse...

20
  In a normal state  
The Status Monitor displays the state of the projector 
in three lines.
:   Displays the projector condition. While the 
lamp is on, the selected port is displayed.
Displayed conditions are:
STANDBY: The projector is in standby mode.
WARM UP: The projector is warming up.
SEARCHING: The projector is searching an input signal.
COOL DOWN:  
The projector is cooling down.
:   While the lamp is on, the detected input signal condition is 
displayed. Otherwise, the projector's...

21
Status Monitor  
  Error states: 
The Status Monitor displays error warnings in capital 
letters. To resolve the errors, refer to the sections 
"Related messages" (11 4) and "Regarding the 
indicator lamps" (11 5, 11 6). 
Displayed warnings:
COVER: The lamp cover has not been securely fastened. 
Refer to the blinking LAMP indicator in the table (11 5).
FA N: The cooing fan is not operating. 
Refer to the blinking TEMP indicator in the table (11 6).
LAMP: The lamp does not light....

22
When the projector is acting normally, or is 
displaying an AIR FLOW, COLD or FILTER 
error, press the FUNCTION button on the 
control panel or press the ENTER button on 
the remote control for three seconds. The 
monitor backlight turns on.
  To display the setup information including 
usage time
Use the ◄/► buttons to switch display. 
      
Usage time: The Status Monitor displays the 
lamp time (the hours the present lamp has 
been used), the filter time (the hours the 
air filter has been used)...

23
AC240V35°C
7FILTERERRO
1PREVIOUS
  To display error history 
Press the ▲ button to display the previous 
error log. If a warning has been displayed, the 
first previous error log will be current error. 
The Status Monitor displays the log number, 
the error that occurred, and the supplied 
voltage and peripheral temperature at that 
time. Press the ► button to display the time 
when each error occurred. 
Use the ▲/▼ buttons to change the 
log. The display switches with the 
◄/► buttons to each log....

24
1.Make sure the power cord is firmly and 
correctly connected to the projector and 
the outlet.
Turning on the power
2.Make sure the POWER indicator is 
steady orange (11 5). Then remove the 
lens cover.
3.Press the STANDBY/ON button on the  
projector or the ON button on the remote  
control.The projection lamp will light up and POWER indicator will begin 
blinking green. When the power is completely on, the indicator will stop 
blinking and become steady green (11 5).
Power on/off
To display the...

25
Operating
Operating
1.
Adjusting the volume
Use the VOL + / - buttons to adjust the volume. 
A dialog will appear on the screen to aid you in 
adjusting the volume. If you do not do anything, 
the dialog will automatically disappear after a few 
seconds.
• When  is selected for current source, the volume adjustment is 
disabled. See the AUDIO SOURCE item of AUDIO menu (57).
• Even if the projector is in standby mode, the volume is adjustable when both 
of the following conditions are true:
-  
An...

26
Operating
1.Press the INPUT button on the projector.  
Each time you press the button, the projector 
switches its input port from the current port as per 
below.
Selecting an input signal
1.Press the COMPUTER 1 / 2, LAN, USB TYPE A / B, HDMI 1 / 2, 
COMPONENT, S-VIDEO or VIDEO button on the remote control.  
The port corresponding to each button is selected as per below.
ButtonPorts
COMPUTER 1COMPUTER IN1
COMPUTER 2COMPUTER IN2
LANLAN
USB TYPE AUSB TYPE A
USB TYPE BUSB TYPE B
HDMI 1HDMI 1
HDMI 2HDMI...