HP Z5200 Owners Manual

11.Carefully pull the atta chment clip forward until you can lift the bottom left corner of the Top Cover
approximately 10 mm.
12. Lift the Top Cover of the printer sufficiently to gain access to the Front Panel ribbon cable.
13.Unroute the Front Panel ribbon cable from the two  cable clamps on the bottom surface of the Top
Cover.
ENWW Top Cover 207 

14.Lift the Top Cover off the printer.
NOTE: When you finish installing or  replacing this component, you must perform the necessary
Service Calibrations. To find which ca librations you must perform, refer to 
Service Calibration Guide to
Removal and Installation on page 170.
Window Position Sensor
Removal
NOTE:Switch off the printer and remove the power cable.
1.Remove the Right Cover (refer Right Cover on page 185).
2. Remove the Left Cover (refer to 
Left Cover on page 188).
3. Remove the Front Panel...

6.Remove one T-15 screw that secures the  Window Position Sensor to the printer.
7.Remove the Window Position Sensor to the printer.
NOTE: When you finish installing or  replacing this component, yo u must perform the necessary
Service Calibrations. To find which calibrations you must perform, refer to 
Service Calibration Guide to
Removal and Installation on page 170 .
Ink Supply Tubes Support Rail
Removal
NOTE: Switch off the printer and remove the power cable.
1.Remove the Right Cover (refer Right...

6.Remove the Ink Supply Tubes from the Ink Supply Tubes Support Rail.
7.Remove the T-15 screws  that secure the rear attachment brackets to the Ink Supply Tubes Support
Rail.
8. Remove the T-15 screw that attaches the right bonding cable.
210 Chapter 6   Removal and Installation ENWW 

9.Remove the T-15 screw that attaches the left bonding cable.
10.Remove the T-15 screw that attaches the left bonding cable.
11.Remove two T-15 screws that secure the Ink Supply Tubes Support Rail to the right Top Cover
Support.
ENWW Ink Supply Tubes Support Rail 211 

12.Remove two T-15 screws that se cure the Ink Supply Tubes Support Rail to the left Top Cover
Support.
13. Slide the rail enough to disengage it from the attachment lug.
14.Carefully slide the Ink Supply Tubes Support Rail to  the left until the right end is clear of the right
Top Cover Support.
212 Chapter 6   Removal and Installation ENWW 

15.Remove the Ink Supply Tubes Support Rail from the printer.
NOTE: When you reinstall the Ink Supply Tubes Support Rail make sure that the attachment lug
is correctly engaged with the right Top Cover Support.
NOTE: When you reinstall the Ink Supply Tubes Support Rail make sure all the attachment
brackets and bonding leads are correctly connecte d. These are important to avoid electrostatic
interference being generated.
NOTE: When you finish installing or  replacing this component, yo u must perform the...

Service Station
Removal
NOTE:Switch off the printer and remove the power cable.
1.Remove the Right Cover (refer Right Cover on page 185).
2. Disconnect the Ink Supply Station ribbon connecto r and two lower connectors from the PrintMech
PCA.
NOTE: The Ink Supply Station ribbon connector has to be disconnected so the other cables can
an be unrouted.
3. Unroute the two cables disconnected in step 2 from the two cable clamps below the PrintMech
PCA.
4.Remove the grounding cable attachm ent screw from the...

5.Disconnect connector from the Drop Dete ctor Motor and Drop Detector Sensor.
6.Unroute the cables disconnected in steps 4 and 5 from the two cable clamps.
7.Disconnect the Aerosol Fan Assembly inline connector.
ENWW Service Station 215 

8.Loosen the T-10 uncapping screw sufficiently so  you can manually move the Carriage Assembly
in step 9.
9. Push the Carriage Assembly into the print path to  gain access to two T-15 screws that secure the
Service Station to the Carriage Rail.
10. Use a allen key provided in the tool kit to remove  two allen screws that secure the Service Station
to the Carriage Rod.
NOTE: Support the Service Station so it does not  fall when you remove the attachment screws.
216 Chapter 6   Removal and Installation ENWW