HP Z5200 Owners Manual

4.Unclip the spring from the attachment points on the Media Lever and Left Cover.
5.Remove three T-15 screws that secure the Media Lever.
6.Lift the Media Lever of the mounting.
ENWW Media Lever 197 

7.Remove the Media Lever from the printer.
Media Lever Position Sensor
Removal
NOTE: Switch off the printer and remove the power cable.
1.Raise the Media Lever.
2. Remove the Left Cover (refer 
Left Cover on page 188).
3. Disconnect the Media Lever Position Sensor.
4.Remove one T-15 screw that secures the Media Lever Position Sensor to the Scan Side Panel.
198 Chapter 6   Removal and Installation ENWW 

5.Rotate the Media Lever Position Sensor vertically to disengage the attachment lug from the Scan
Side Panel.
6.Remove the Media Lever Position Sensor.
NOTE: When you finish installing or  replacing this component, yo u must perform the necessary
Service Calibrations. To find which calibrations you must perform, refer to 
Service Calibration Guide to
Removal and Installation on page 170 .
Cutter Assembly
Removal
NOTE: Switch off the printer and remove the power cable.
1.Remove the Left Cover Finishing...

2.Fully loosen the cutter rail end cap attachment screw.
3.Remove the cutter rail end cap.
4.Slide the Cutter Assembly out of the printer.
NOTE: When you install the new Cutter Assembly, fo llow the installation instructions provided
with the new Cutter Assembly.
Right Rear Tray Support
Removal
NOTE: Switch off the printer and remove the power cable.
1.Remove the Rear Tray (refer Rear Tray on page 194).
2. Remove the Right Cover (refer 
Right Cover on page 185).
200 Chapter 6   Removal and Installation...

3.Remove the Left  Cover (refer Left Cover on page 188).
4. Remove the Rear Cover (refer 
Rear Cover on page 195).
5. Remove two T-15 screws that secure the  Right Rear Tray Support to the printer.
6.Rotate the Right Rear Tray Support counterclockwise approximately 30 degrees.
7.Remove the Right Rear Tray Support from the printer.
Left Rear Tray Support
Removal
NOTE: Switch off the printer and remove the power cable.
1.Remove the Rear Tray (refer Rear Tray on page 194).
2. Remove the Right Cover (refer...

3.Remove the Left Cover (refer Left Cover on page 188).
4. Remove the Rear Cover (refer 
Rear Cover on page 195).
5. Remove two T-15 screws that secure the  Left Rear Tray Support to the printer.
6.Rotate the Left Rear Tray Support clockwise approximately 30 degrees.
7.Remove the Left Rear Tray Support from the printer.
202 Chapter 6   Removal and Installation ENWW 

Front Panel
Removal
NOTE:Switch off the printer and remove the power cable.
1.Open the Window.
2.With strong pressure, squeeze the top edge of the front panel enough to release the attachment
clips, and begin rotating the Front Panel vertically in the next step.
3.Rotate the front panel vertically.
ENWW Front Panel 203 

4.Disconnect the interface cable from the Front Panel.
5.Push in the clip that prevents the Ferrite Core from being removed.
6.Slide the Ferrite Core out of the brackets.
204 Chapter 6   Removal and Installation ENWW 

7.Remove the Front Panel.
NOTE: When you reinstall the Front Panel, you must ma ke sure that the Ferrite Core is correctly
positioned. The Ferrite Core is necessary to avoid electrostatic interference being generated.
NOTE: When you finish installing or  replacing this component, yo u must perform the necessary
Service Calibrations. To find which calibrations you must perform, Refer to 
Service Calibration Guide
to Removal and Installation on page 170.
Top Cover
Removal
NOTE: Switch off the printer and...

8.Remove the front T-15 screw that  secures the front left side of the Top Cover to the printer.
9.Carefully pull the attachment clip  forward until you can lift the bottom left corner of the Top Cover
approximately 10 mm.
10. Remove the front T-15 screw that  secures the front left side of the Top Cover to the printer.
206 Chapter 6   Removal and Installation ENWW