HP PhotoSmart C6283 User Manual

Solution:Change the  Paper Type setting to match the type of paper loaded in the
input tray.
For more information, see:
•“
Set the copy paper type” on page 87
•“
Set the paper type for printing” on page 47
Cause: The print quality setting on the HP All-in-One is set too low.
Solution: Load high-quality paper in the input tray and print the image with a high
print quality sett ing, such as Best, Maximum dpi , or High Resolution . Always make
sure the paper you are printing on is flat. For best results...

Solution:Make sure the Two-sided printing a ccessory on the back of the HP All-
in-One is securely installed.
Ink is overspraying the paper when I print a photo
Cause: A small amount (a few millimeters) of overspray is common when making
a copy of a photo. If there are more than a few millimeters of overspray, it might mean
the HP All-in-One thinks the paper loaded is wider than it actually is.
TIP: One way to tell if ink is  overspraying the paper is  to check the back side of
pages you print after...

Solution:Remove all paper from the input tray. Load a stack of envelopes in the
input tray, with the envelope flaps facing up and to the left.
NOTE: To avoid paper jams, tuck the flaps inside the envelopes.
Related topics
“
Load envelopes” on page 40
Cause: The wrong type of envelope is loaded.
Solution: Do not use shiny or embossed envelopes or envelopes that have clasps
or windows.
Borderless printing produces unexpected results
Cause: Printing a borderless image from a non-HP software application...

Solution:Load paper in the input tray.
For more information, see:
“
Load paper” on page 36
Cause: The print head assembly has stalled.
Solution: Turn the HP All-in-One off and open the ink cartridge door. Remove any
objects that are blocking the print head assembly (including any packing materials),
and then turn the HP All-in-One on again.
Cause: The computer is not communicating with the HP All-in-One.
Solution: If the HP All-in-One is not properly connected to the computer,
communication errors can...

Solution:The printer driver status might have changed to either  offline or stop
printing .
To check the printer driver status
1. In the HP Solution Center, click the device tab.
2. Click  Settings .
3. Click  Status .
If the status is  offline or stop printing , change the status to  ready.
Cause: A deleted print job is still in the queue.
Solution: A print job might remain in the queue after it has been cancelled. The
cancelled print job jams the queue and prevents the next print job from printing....

the HP All-in-One and plugged into a power outlet. Press the On button to turn on the
HP All-in-One.
Cause: The HP All-in-One is busy with another task.
Solution: If the HP All-in-One is performing another task such as copying or
scanning, your print job will be delayed until the HP All-in-One completes the current
task.
Some documents take a long time to print. If nothing has printed several minutes after
you sent a print job to the HP All-in-One, check your computer to see if there are any
messages....

Solution:Clear the paper jam.
For more information, see:
“
Clear paper jams” on page 111
Cause: The print head assembly has stalled.
Solution: Turn the HP All-in-One off and open the ink cartridge door. Remove any
objects that are blocking the print head assembly (including any packing materials),
and then turn the HP All-in-One on again.
Cause: The HP All-in-One is out of paper.
Solution: Load paper in the input tray.
For more information, see:
“
Load paper” on page 36
The pages in my document came out...

Solution:Verify that you have selected the proper paper size setting for your
project. Make sure that you have loaded the correct paper size in the input tray.
Cause: The paper guides are not positioned correctly.
Solution: Remove the stack of paper from the input tray, reload the paper, and then
slide the paper width guide inward until it stops at the edge of the paper.
For more information, see:
“
Load paper” on page 36
Cause: A stack of envelopes is loaded incorrectly.
Solution: Remove all paper from...

Solution:Make sure the layout of the document you are trying to print fits on a paper
size supported by the HP All-in-One.
To preview the print layout
1. Load the correct paper size into the input tray.
2. Preview your print job before sending it to the HP All-in-One.
3. Check the graphics in the document to make  sure that the current size fits within
the printable area of the HP All-in-One.
4. Cancel the print job if the graphics do not fit in the printable area of the page.
TIP: Some software...

Memory card troubleshooting
Use this section to solve these memory card problems:
•
My memory card no longer works in my digital camera
•
The HP All-in-One does not read the memory card
•
The Photo light next to the memory card slots is blinking
•
The Attention light blinks when I insert my memory card
•
The photos on the memory card do not transfer to my computer
•
Memory card is not available
•
The file name appears as meaningless text
•
Other users on the network  can access my memory card
•
Error...