HP Photosmart C4599 User Manual

							
3.In the  Print Settings  area, click Printer Toolbox .
NOTE:You can also open the  Printer Toolbox from the Print Properties  dialog
box. In the  Print Properties  dialog box, click the  Features tab, and then click
Printer Services .
NOTE:You can also open the  Printer Toolbox from the Print Properties  dialog
box. In the  Print Properties  dialog box, click the  Features tab, and then click the
Printer Services  button.
The Printer Toolbox  appears.
4. Click the  Device Services  tab.
5. Click  Align the Print Cartridges .
6. When prompted, ensure plain white letter or A4 paper is loaded in the input tray, then
press the button next to  OK.
NOTE: If you have colored paper loaded in the input tray when you align the print
cartridges, the alignment will fail. Load unused plain white paper into the input
tray, and then try the alignment again.
The product prints a print cartridge alignment sheet.
7. Load the page print side down on the right front corner of the glass, and then press
the button next to  OK to scan the page.
When the On button stops flashing, the alignment is complete and the page can be
removed. Recycle or  discard the page.
Clean the print cartridges
Use this feature when the self-test report shows streaking, white lines through any of the
lines of color or when a color is muddy after installing a print cartridge for the first time.
Do not clean print cartridges unnecessarily, as this wastes ink and shortens the life of the
ink nozzles.
To clean the print cartridges fr om the HP Photosmart Software
1. Load letter, A4, or legal unused plain white paper into the input tray.
2. In the HP Solution Center, click  Settings.
3. In the  Print Settings  area, click Printer Toolbox .
NOTE:You can also open the  Printer Toolbox from the Print Properties  dialog
box. In the  Print Properties  dialog box, click the  Features tab, and then click
Printer Services .
The Printer Toolbox  appears.
4. Click the  Device Services  tab.
5. Click  Clean the Print Cartridges .
Chapter 11
88 Maintain the HP All-in-One
Maintain the HP All-in-One
 
						

							
6.Follow the prompts until you are satisfied with the quality of the output, and then click
Done .
7. Follow the prompts until you are satisfied with the quality of the output, and then click
Done .
There are three stages of cleaning. Each stage lasts from one to two minutes, uses
one sheet of paper, and uses an increasing amount of ink. After each stage, review
the quality of the printed page. You should only initiate the next phase of cleaning if
the print quality is poor.
If print quality still seems poor after you clean the print cartridges, try cleaning the
print cartridge contacts before replacing the affected print cartridge.
Related topics
•“
Clean the print cartridge contacts” on page 89
•“
Replace the print cartridges” on page 81
Clean the print cartridge contacts
CAUTION: Do not clean the print cartridge contacts unless you are having a problem
with print quality and other measures have not been successful. For more information,
see  “
Print quality troubleshooting” on page 115 .
Clean the print cartridge contacts if you get repeated messages on your computer screen
prompting you to check a print cartridge after you already have cleaned or aligned the
print cartridges.
Before cleaning the print cartridge contacts, remove the print cartridge and verify that
nothing is covering the print cartridge contacts, then reinstall the print cartridge. If you
continue to get messages to check the print cartridges, clean the print cartridge contacts.
Make sure you have the following materials available:
•Dry foam rubber swabs, lint-free cloth, or any soft material that will not come apart or
leave fibers.
TIP: Coffee filters are lint-free and work well for cleaning print cartridges.
•Distilled, filtered, or bottled water (tap water might contain contaminants that can
damage the print cartridges).
CAUTION: Do not use platen cleaners or alcohol to clean the print cartridge
contacts. These can damage the print cartridge or the product.
To clean the print cartridge contacts
1. Make sure the product is turned on.
CAUTION: If the product is turned off when you open the print cartridge door to
access the print cartridges, it will not release the cartridges for changing. You
might damage the product if the print cartridges are not docked safely when you
try to remove them.
2. Open the print cartridge door.
The print carriage moves to the far right side of the product.
Work with print cartridges 89
Maintain the HP All-in-One
 
						

							
3.Wait until the print carriage is idle and silent, and then unplug the power cord from
the back of the product.
4. Lightly press down on the print cartridge to release it, and then pull it towards you out
of the slot.
NOTE: Do not remove both print cartridges at the same time. Remove and clean
each print cartridge one at a time. Do not leave a print cartridge outside the product
for more than 30 minutes.
5. Inspect the print cartridge contacts for ink and debris buildup.
6. Dip a clean foam rubber swab or lint-free cloth into distilled water, and squeeze any
excess water from it.
7. Hold the print cartridge by its sides.
8. Clean only the copper-colored contacts. Allow the print cartridges to dry for
approximately ten minutes.
1Copper-colored contacts
2Ink nozzles (do not clean)
9.Hold the print cartridge with the HP logo on top, and insert the print cartridge back
into the slot. Make sure you push the print cartridge in firmly until it snaps into place.
Chapter 11
90 Maintain the HP All-in-One
Maintain the HP All-in-One
 
						

							
10.Repeat if necessary for the other print cartridge.
11. Gently close the print cartridge door and plug the power cord into the back of the
product.
Related topics
•“
Clean the area around the ink nozzles” on page 91
•“
Replace the print cartridges” on page 81
Clean the area around the ink nozzles
If the product is used in a dusty environment, a small amount of debris might accumulate
inside the product. This debris can includ e dust, hair, carpet, or clothing fibers. When
debris gets on the print cartridges, it can cause ink streaks and smudges on printed pages.
Ink streaking can be corrected by cleaning around the ink nozzles as described here.
NOTE: Clean the area around the ink nozzles only if you continue to see streaks
and smudges on your printed pages after you have already cleaned the print
cartridges by using the software you installed with the product.
Make sure you have the following materials available:
Work with print cartridges 91
Maintain the HP All-in-One
 
						

							
•Dry foam rubber swabs, lint-free cloth, or any soft material that will not come apart or
leave fibers.
TIP: Coffee filters are lint-free and work well for cleaning print cartridges.
•Distilled, filtered, or bottled water (tap water might contain contaminants that can
damage the print cartridges).
CAUTION: Do not touch the copper-colored co ntacts or ink nozzles. Touching
these parts can result in clogs, ink failure, and bad electrical connections.
To clean the area around the ink nozzles
1. Make sure the product is turned on.
CAUTION: If the product is turned off when you open the print cartridge door to
access the print cartridges, it will not release the cartridges for changing. You
might damage the product if the print cartridges are not docked safely when you
try to remove them.
2. Open the print cartridge door.
The print carriage moves to the far right side of the product.
3.Wait until the print carriage is idle and silent, and then unplug the power cord from
the back of the product.
4. Lightly press down on the print cartridge to release it, and then pull it towards you out
of the slot.
NOTE: Do not remove both print cartridges at the same time. Remove and clean
each print cartridge one at a time. Do not leave a print cartridge outside the product
for more than 30 minutes.
5. Place the print cartridge on a piece of paper with the ink nozzles facing up.
6. Lightly moisten a clean foam rubber swab with distilled water.
7. Clean the face and edges around the ink nozzle area with the swab, as shown below.
Chapter 11
92 Maintain the HP All-in-One
Maintain the HP All-in-One
 
						

							
1Nozzle plate (do not clean)
2Face and edges around the ink nozzle area
CAUTION:Do not clean the nozzle plate.
8. Hold the print cartridge with the HP logo on top, and insert the print cartridge back
into the slot. Make sure you push the print cartridge in firmly until it snaps into place.
9.Repeat if necessary for the other print cartridge.
10. Gently close the print cartridge door and plug the power cord into the back of the
product.
Related topics
“
Clean the print cartridges” on page 88
Work with print cartridges 93
Maintain the HP All-in-One
 
						

							
Print a self-test report
If you are experiencing problems with printing, print a self-test report before you replace
the print cartridges. This report provides useful information on several aspects of your
product, including your print cartridges.
To print a self-test report
1. Load letter or A4 unused plain white paper into the input tray.
2. Press and hold the Cancel button and then press the  Start Copy Color button.
The product prints a self-test report, which  might indicate the source of the printing
problem. A sample of the ink test area of the report is shown below.
3. Make sure the test patterns show a complete grid and the thick color lines are
complete.
• If more than a few lines in a pattern are broken, this might indicate a problem with
the nozzles. You might need to clean the print cartridges.
• If the black line is missing, faded, streaked, or shows lines, this might indicate a problem with the black or photo print cartridge in the right slot.
• If any of the color lines are missing, faded, streaked, or show lines, this might indicate a problem with the tri-color print cartridge in the left slot.
Related topics
•“
Clean the print cartridges” on page 88
•“
Replace the print cartridges” on page 81
•“
Align the print cartridges” on page 87
Clean the HP All-in-One
To ensure that your copies and scans remain clear, you might need to clean the glass
and lid backing. You might also want to dust the exterior of the HP All-in-One.
Chapter 11
94 Maintain the HP All-in-One
Maintain the HP All-in-One
 
						

							
TIP:You can purchase an HP Cleaning Kit for Inkjet Printers and All-in-Ones
(Q6260A) that provides everything needed to safely clean your HP product. For more
information, go to: 
www.shopping.hp.com/accessories-store/printer .
This section contains the following topics:
•
Clean the exterior
•
Clean the glass
•
Clean the lid backing
Clean the exterior
Use a soft cloth or slightly moistened sponge to wipe dust, smudges, and stains off the
case. The interior of the HP All-in-One does not require cleaning. Keep fluids away from
the control panel and the interior of the HP All-in-One.
CAUTION: To avoid damage to the exterior of the HP All-in-One, do not use alcohol
or alcohol-based cleaning products.
Clean the glass
Fingerprints, smudges, hair, and dust on the  main glass surface slow down performance
and affect the accuracy of the copy and scan features.
To clean the glass
1. Turn off the product, unplug the power cord, and raise the lid.
2. Clean the glass with a soft cloth or sponge slightly moistened with a nonabrasive
glass cleaner.
CAUTION: Do not use abrasives, acetone, benzene, or carbon tetrachloride on
the glass, since they can damage it. Do not place or spray liquid directly on the
glass. The liquid might seep under the glass and damage the product.
3. Dry the glass with a dry, soft, lint-free cloth to prevent spotting.
4. Turn on the product.
Clean the lid backing
Minor debris can accumulate on the white document backing located underneath the lid
of the HP All-in-One.
To clean the lid backing
1.Turn off the product, unplug the power cord, and raise the lid.
2. Clean the white document backing with a soft cloth or sponge slightly moistened with
a mild soap and warm water.
Wash the backing gently to loosen debris. Do not scrub the backing.
Clean the HP All-in-One 95
Maintain the HP All-in-One
 
						

							
3.Dry the backing with a dry, soft, lint-free cloth.
CAUTION: Do not use paper-based wipes, as these might scratch the backing.
4.If further cleaning is needed, repeat the  previous steps using isopropyl (rubbing)
alcohol, and wipe the backing thoroughly with a damp cloth to remove any residual
alcohol.
CAUTION: Be careful not to spill alcohol on the glass or exterior of the product,
as this might damage it.
5. Plug in the power cord, and then turn on the product.
Turn off the HP All-in-One
To avoid damaging the product, you must properly shut it down by using the On button
located on the product. Wait until the On light turns off before you unplug the power cord
or turn off a power strip.
Chapter 11
96 Maintain the HP All-in-One
Maintain the HP All-in-One
 
						

							
12 Shop for ink supplies
For a list of print cartridge numbers, see the printed documentation that came with the
HP All-in-One. You can also use the software that came with the HP All-in-One to find
out the reorder number for all the print cartridges. You can order print cartridges online
from the HP Web site. Additionally, you can contact a local HP reseller to find out the
correct print cartridge reorder numbers for your product and purchase print cartridges.
To order genuine HP supplies for the HP All-in-One, go to 
www.hp.com/buy/supplies . If
prompted, choose your country/region, follow the prompts to select your product, and
then click one of the shopping links on the page.
NOTE: Ordering print cartridges online is not supported in all countries/regions. If it
is not supported in your country/region, contact a local HP reseller for information
about purchasing print cartridges.
To order print cartridges from your desktop
▲ Click the  Shop for HP Supplies  icon on your desktop to connect to HP SureSupply.
You will see a list of original HP printing supplies that are compatible with your product,
as well as options to conveniently purchase the supplies you need (options vary by
country/region).
If you deleted this icon fr om your desktop, click the  Start menu, point to the  HP folder,
then click  Shop for Supplies .
To order print cartridges through the HP Photosmart Software
1. In the HP Solution Center, click  Settings, point to  Print Settings , and then click
Printer Toolbox .
NOTE:You can also open the  Printer Toolbox from the Print Properties  dialog
box. In the  Print Properties  dialog box, click the  Features tab, and then click the
Printer Services  button.
2.Click the  Estimated Ink Levels  tab.
3. Click  Print Cartridge Ordering Information .
The print cartridge reorder numbers appear.
4. Click  Order Online .
HP sends detailed printer information, including model number, serial number, and
ink supply levels, to an authorized on line reseller. The supplies you need are
preselected; you can change quantities, add or remove items, and then check out.
Shop for ink supplies 97
Shop for ink supplies