HP LaserJet Enterprise P3015 User Manual

7.Push down on the DIMM until both latches engage the DIMM.
XOX O
XO
XO XOXO
XOX
O
XO XO XOXO
X O
XO
XO
XOX O
XO
XO XO
XO XOXO
XO XO XO
XO XO XO
XO XOXO
XO XO
XO
XOXO XO
XOXO XO
X O
XO XOXO
XO XOXO
XO
XOXOXO XO
XO
XO XO
XO
XIOXIOXIXO
OXIXO
XI
OXIO XI
OXI O
XIX O
OXIXO
XI
OXIO XI
OXIO XIXO
OXIXO
XI
OXIO XIO
XIO XIXO
OXIXO
XIO
XIO
NOTE:
If you have difficulty inserting the DIMM, make sure the notch on the bottom of the DIMM
is aligned with the bar in the slot. If the DIMM still does not go in, make sure...

9.Reconnect the interface cables and the power cord.
10.Turn the product on.
Check DIMM installation
After installing the DIMM, make sure that the installation was successful.
1.Turn the product on. Check that the Ready light is illuminated after the product has gone through
the startup sequence. If an error message appears, a DIMM might have been incorrectly installed.
See 
Interpret control-panel messages on page 147.
2. Print a configuration page (see 
Print the information and show-me-how pages on...

NOTE:Overusing permanent resources or downloading them while the product is printing might affect
product performance or the ability to print complex pages.
Enable memory for Windows
1. Windows XP and Windows Server 2003 (using the default Start menu view) : Click Start, click
Settings , and then click  Printers and Faxes .
-or-
Windows 2000, Windows XP, and Windows Server 2003 (using the Classic Start menu
view) : Click Start , click Settings , and then click  Printers.
-or-
Windows Vista : Click Start,...

Install internal USB devices
The product has two internal USB ports.
1.Turn the product off and disconnect the power cord.
2
1
2.Disconnect all interface cables.
132 Chapter 9   Manage and maintain the product ENWW
 

3.Remove the right-side panel by sliding it towards the rear of the product to unlatch it.
2
1
4.Locate the USB ports near the bottom of the formatter board. Insert the USB device into one of the
ports.
ENWW Install memory, internal USB devices, and external I/O cards 133
 

5.Reinstall the right-side panel. Align the tabs on the panel with the slots in the product, and push
the panel toward the front of the product until it latches into place.
2
1
6.Reconnect the interface cables and the power cord.
7.Turn the product on.
134 Chapter 9   Manage and maintain the product ENWW
 

Install EIO cards
Install an EIO card1.Turn off the product.
2. Remove the two screws and cover plate from the EIO slot on the back of the product.
3.Install the EIO card in the EIO slot and tighten the screws.
ENWW Install memory, internal USB devices, and external I/O cards 135
 

4.If the EIO card requires a cable connection, connect the cable.
5.Turn on the product, and then print a configuration page to verify that the new EIO card is
recognized. See 
Print the information and show-me-how pages on page 108.
NOTE: When you print a configuration page, an HP Jetdirect configuration page that contains network
configuration and status information also prints.
Remove an EIO card
1.Turn off the product.
2. Disconnect any cables from the EIO card.
3. Loosen the two screws from the EIO...

Clean the product
During the printing process, paper, toner, and dust particles can accumulate inside the product. Over
time, this buildup can cause print-quality problems, such as toner specks or smearing (see 
Solve print-
quality problems on page 182).
Clean the exterior
Use a soft, damp, lint-free cloth to wipe dust, smudges, and stains off of the exterior of the device.
Clean the paper path
Create and use the cleaning page1.Press the  Menu button 
.
2. Press the up arrow or down arrow 
/ to...

Upgrade the firmware
This product has remote firmware update (RFU) capability. Use this information to upgrade the product
firmware.
Determine the current firmware version
1.Press the  Menu button .
2. Press the down arrow 
 to highlight the  INFORMATION menu, and then press the  OK button.
3. Press the down arrow 
 to highlight the  PRINT CONFIGURATION  option, and then press the
OK  button to print.
The firmware datecode is listed on the configuration page in the section called  Device Information.
The...