HP LaserJet Enterprise P3015 User Manual

Tray and bin capacity
Tray or binPaper typeSpecificationsQuantity
Tray 1PaperRange:
60 g/m
2 (16 lb) bond to 199 g/m2
(53 lb) bond
Maximum stack height: 12 mm
(0.5 in)
Equivalent to 100 sheets of 75
g/m
2 (20 lb) bond
Envelopes75 g/m2 (20 lb) bond to 90 g/m2
(24 lb) bond
Up to 10 envelopes
Labels0.10 to 0.14 mm (0.004 to 0.005
in) thickMaximum stack height: 12 mm
(0.5 in)
Transparencies0.10 to 0.14 mm (0.004 to 0.005
in) thickMaximum stack height: 12 mm
(0.5 in)
Tray 2 and the optional 500-sheet...

Special paper or print media guidelines
This product supports printing on special media. Use the following guidelines to obtain satisfactory
results. When using special paper or print media, be sure to set the type and size in the printer driver
to obtain the best results.
CAUTION:HP LaserJet products use fusers to bond dry toner particles to the paper in very precise
dots. HP laser paper is designed to withstand this extreme heat. Using inkjet paper could damage the
product.
Media typeDoDo not...

Load trays
Paper orientation for loading trays
If you are using paper that requires a specific orientation, load it according to the information in the
following table.
TraySingle-sided printingAutomatic duplex printingEnvelopes
Tray 1Face-up
Top edge leading into the productFace-down
Bottom edge leading into the
productFace-up
Short, postage end leading into
the product
All other traysFace-down
Top edge at the front of the trayFace-up
Bottom edge at the front of the
trayPrint envelopes only from Tray...

Load Tray 1  
NOTE:The product might print at a slower speed when using Tray 1.
CAUTION: To avoid jams, do not load trays while the product is printing. Do not fan the paper. Fanning
can cause misfeeds.
TIP: To see an animation of this procedure go to this Web site: www.hp.com/go/ljp3010-load-tray1.
1.Open Tray 1.
2.Pull out the tray extension.
82 Chapter 6   Paper and print media ENWW
 

3.Load the paper into the tray. Make sure that the paper fits under the tabs and below the maximum-
height indicators.
NOTE: For information about loading paper that requires a specific orientation, see Paper
orientation for loading trays on page 81.
4. Adjust the side guides so that they lightly touch the paper stack but do not bend the paper.
ENWW Load trays 83
 

Load Tray 2 or an optional 500-sheet tray
CAUTION:To avoid jams, do not load trays while the product is printing.
CAUTION:Do not fan the paper. Fanning can cause misfeeds.
TIP:To see an animation of this procedure go to this Web site: www.hp.com/go/ljp3010-load-tray2.
1.Pull the tray out and lift up slightly to remove it completely from the product.
1
2.Pinch the release that is located on the left guide and slide the side guides to the correct paper
size.
84 Chapter 6   Paper and print media ENWW
 

3.Pinch the release that is located on the rear paper guide and slide it to the correct paper size.
ENWW Load trays 85
 

4.Load the paper into the tray. Make sure that the stack is flat at all four corners and that the top of
the stack is below the maximum-height indicators.
NOTE: For information about loading paper that requires a specific orientation, see Paper
orientation for loading trays on page 81.
For A6-size paper, stack the paper no higher than the bottom height indicator.
5. Slide the tray completely into the product.
2
1
2
2
86 Chapter 6   Paper and print media ENWW
 

Configure trays
NOTE:If you have used other HP LaserJet product models, you might be accustomed to configuring
Tray 1 to  First mode or  Cassette  mode. For this product, setting  TRAY 1 SIZE to the ANY SIZE  setting
and setting  TRAY 1 TYPE  to ANY TYPE is equivalent to  First mode. Setting  TRAY 1 SIZE and TRAY 1
TYPE  to any other settings is equivalent to  Cassette mode.
The product automatically prompts you to configure a tray for type and size in the following situations:
●When you load paper into...

3.Press the down arrow  to highlight the size or type setting for the desired tray, and then press the
OK  button.
4. Press the up arrow 
 or the down arrow  to highlight the size or type. If you select a custom size,
select the unit of measure, and then set the X dimension and the Y dimension.
5. Press the  OK button to save your selection.
6. Press the  Menu button 
 to exit the menus.
Select the paper by source, type, or size
Three settings affect how the printer driver tries to pull paper when you...