HP LaserJet Enterprise P3015 User Manual

Lock the control panel menus
You can lock various menus on the control panel by using the embedded Web server.
1.Open the embedded Web server by entering the product IP address into the address line of a Web
browser.
2. Click the Settings  tab, and then click the  Security link.
3. Click the Device Security Settings  button.
4. In the  Control Panel Access Lock  area, select the level of security that you want.
Security levelLocked menus
Minimum Menu Lock●The 
RETRIEVE JOB  menu requires a PIN for...

Lock the formatter
The formatter area, on the back of the product, has a slot that you can use to attach a security cable.
Locking the formatter prevents someone from removing valuable components from it.
120 Chapter 9   Manage and maintain the productENWW
 

Manage supplies
Use genuine HP print cartridges for the best printing results.
Print-cartridge storage
Do not remove the print cartridge from its package until you are ready to use it.
CAUTION:To prevent damage to the print cartridge, do not expose it to light for more than a few
minutes.
HP policy on non-HP print cartridges
Hewlett-Packard Company cannot recommend the use of non-HP print cartridges, either new or
remanufactured.
NOTE: Any damage caused by a non-HP print cartridge is not covered under...

Replace supplies and parts
Supply replacement guidelines
Keep the following guidelines in mind when setting up the product.
●Provide enough space above and in the front of the product for removing supplies.
● Place the product on a flat, sturdy surface.
Change the print cartridge
When a print cartridge reaches the end of its estimated useful life, the control panel displays a 
BLACK
CARTRIDGE VERY LOW  message. You do not need to replace the supply at this time unless print
quality is no longer...

2.Remove the used print cartridge from the product.
2
3
3.Remove the new print cartridge from the bag. Place the used print cartridge in the bag for recycling.
4.Grasp the front and back of the print cartridge, and distribute the toner by gently rocking the print
cartridge five or six times.
CAUTION: Do not touch the shutter or the surface of the roller.
ENWW Replace supplies and parts 123
 

5.Remove the shipping tape from the new print cartridge. Discard the tape according to local
regulations.
6.Align the print cartridge with the tracks inside the product, and insert the print cartridge until it is
firmly seated.
2
1
3
124 Chapter 9   Manage and maintain the product ENWW
 

7.Close the top cover. After a short time, the control panel should display  Ready.
2
1
3
2
1
3
ENWW Replace supplies and parts 125
 

Install memory, internal USB devices, and external I/O
cards
Overview
The formatter has the following open slots and ports for expanding the products capabilities:
●One dual inline memory module (DIMM) slot for upgrading the product with more memory
● Two internal USB ports for adding fonts, languages, and other third-party solutions
● One external I/O (EIO) slot for adding an external print server, an external hard disk, or a parallel
port
If the product already has an embedded HP Jetdirect print server...

2.Turn the product off and disconnect the power cord.
2
1
3.Disconnect all interface cables.
4.Remove the right-side panel by sliding it towards the rear of the product to unlatch it.
2
1
ENWW Install memory, internal USB devices, and external I/O cards 127
 

5.Remove the DIMM from the antistatic package.
CAUTION: To reduce the possibility of damage caused by static electricity, always wear an
electrostatic discharge (ESD) wrist strap or touch the surface of the antistatic package before
handling DIMMs.
6. Holding the DIMM by the edges, align the notch on the DIMM with the bar in the DIMM slot at an
angle and firmly press the DIMM into the slot until it is fully seated. When installed correctly, the
metal contacts are not visible.
XOX
OXO XOXOX O
XO
X
O XO...