HP Color Laserjet 5 Manual

Standards for Ozone
Standards for exposure to ozone have been established by the Department
of Labor - Occupational Health & Safety Administration (DOL-OSHA) and
the American Conference of Governmental Industrial Hygienists (ACGIH).
These standards are 0.1 ppm as a ceiling limit. All LaserJet family printers
meet these standards when shipped from the factory.
Recommendations for Minimizing Ozone
Exposure
Some people are extremely sensitive to ozone. In such cases, it is advisable
to position the printer...

Laser 
LASERTURVALLISUUS
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
HP Color LaserJet laserkirjoitin on käyttäjän kannalta turvallinen luokan 1
laserlaite. Normaalissa käytssä kirjoittimen suojakotelointi estää
lasersäteen pääsyn laitteen ulkopuolelle.
Kirjoittimen on hyväksynyt Suomessa laserturvallisuuden osalta
Tysuojeluhallitus. Laitteen turvallisuusluokka on määritetty
valtioneuvoston päätksen N:o 472/1985 ja standardin EN 60825 (1991)
mukaisesti.
VAROITUS !
Laitteen käyttäminen muulla kuin...

DECLARATION OF CONFORMITY
According to ISO/IEC Guide 22 and EN 45014
Manufacturer’s Name:Hewlett-Packard Company
Manufacturer’s Address:11311 Chinden Boulevard
Boise, Idaho 83714-1021, USA
declares, that the product
Product Name:Color LaserJet 5/5M
Model Number:C3961A, C3962A
Product Options:All
conforms to the following Product Specifications:
Safety:IEC 950:1991 + A1+A2 / EN 60950:1992+A1+A2
IEC 825:1984 + A1 / EN 60825:1991 Class 1
EMC:CISPR-22:1993 / EN 55022:1994 Class B 
1
CISPR-22:1993 / EN...

C-8 Environmental SpecificationsEN 

D
SIMM Installation
To Install a SIMM
CAUTION Wear an antistatic wrist strap or touch the surface of the antistatic package
before removing the board from its package. When handling the board, wear
an antistatic wrist strap or frequently touch bare metal on the printer.
Follow the instructions in this appendix to install your AdobeÔ PostScriptÔ
SIMM board. 
ENSIMM Installation  D-1 

1Turn the printer off (button out).
2Disconnect the power cord.
3Open the SIMM access door.
4Remove the access panel using a Phillips
screwdriver.
4
1
2
3
D-2 SIMM InstallationEN 

5With the notch (A) pointing downward,
firmly insert the board at a 30° angle into
the farthest open slot to the right.
6Move the board to the right until it snaps
into a position perpendicular to the
printer.
7Replace the access panel.
8Close the access door, reconnect the power
cord, and turn the printer ON. 
6
7
5
8
After installing the PostScript SIMM, see
“Switching printer personalities” in Chapter 5 .
D
SIMM
Installation
ENSIMM Installation  D-3 

·Verification:  To verify successful SIMM installation, refer to Chapter 5
and print out a self test page. If the SIMM has been installed properly,
the self test will show the presence of the SIMM.
If the printer display shows an error message, refer to Chapter 7 for
further information.
D-4 SIMM InstallationEN 

E
Printer Interfaces
Introduction
This appendix contains the following information:
·Switchbox Operation
·Parallel Configuration
·Modular I/O Configuration
·LocalTalk Configuration
·Enhancing  Network Performance
ENPrinter Interfaces  E-1 

Switchbox Operation
If you are using a mechanical switchbox:
·Do not switch when the printer is printing or receiving data (that is, when
the Data light is blinking).
·Do not switch to a host computer that is off, then switch that computer on.
The computer can appear to be sending data.  If a 22 I/O CONFIG ERROR
appears on the printer’s display, reset the printer by using the [RESET] key.
E-2  Printer InterfacesEN