HP Color LaserJet 2605 User Manual

							
Installing memory and font DIMMs
You can install more memory for the printer, and you can also install a font DIMM to print characters
for languages such as Chinese, or for the Cyrillic alphabet.
CAUTIONStatic electricity can damage DIMMs. When handling DIMMs, wear an antistatic
wrist strap, or frequently touch the surface of the DIMM antistatic package and then touch
bare metal on the printer.
1. Print a Configuration page by pressing  (Select ) and  (Cancel Job ) simultaneously. (A
Supplies Status page and possibly an HP Jetdirect Configuration page also print.) If the
Configuration page does not print in your language, see 
Device pages and reports .
2. After the Configuration page prints, turn the printer off and disconnect the power cable.
3.On the left rear side of the printer, open the DIMM door.
ENWW Installing memory and font DIMMs 169
 
						

							
4.Release the locks on each side of the DIMM slot.
5.Remove the DIMM from the antistatic package.
6.Holding the DIMM by the edges as shown in the illustration, align the notches on the DIMM with
the DIMM slot.
170 Chapter 13   Working with memory ENWW
 
						

							
7.Firmly press the DIMM straight into the slot. Firmly close the locks on each side of the DIMM
until they snap into place.
8.Close the DIMM door.
9.Reconnect the power cable and turn the printer on.
10.Go to Checking DIMM installation .
ENWW Installing memory and font DIMMs 171
 
						

							
Checking DIMM installation
Check that the DIMMs are installed correctly and working.
1.Turn the printer on. Check that  the Ready light is on after the printer has completed the startup
sequence. If an error message appears, a DIMM might have been incorrectly installed.
2. Print a Configuration page by pressing 
 (Select ) and  (Cancel Job ) simultaneously. (A
Supplies Status page and possibly an HP Jetdirect Configuration page also print.)
3. Check the Installed Personalities and Options section on the Configuration page and compare it
with the Configuration page printed before the DIMM installation.
4. If the amount of recognized memory has not increased or the font DIMM is not recognized, the
following conditions might exist:
●The DIMM might not be installed correctly. Repeat the installation procedure.
● The DIMM might be defective. Try installing a different DIMM.
5. After you have installed the DIMM correctly, go to 
Enabling memory  if you installed a memory
DIMM or 
Enabling the language-font DIMM for Windows  if you installed a language-font DIMM.
172 Chapter 13   Working with memory ENWW
 
						

							
Enabling memory
If the printer has a new memory DIMM installed, all Windows users of the printer must set the printer
driver to recognize the newly added memory. Macintosh computers automatically recognize new
memory.
To enable memory for Windows
1.On the  Start menu, point to  Settings, and click  Printers or Printers and Faxes .
2. Select this printer and select  Properties.
3. On the  Configure  tab, click More.
4. In the  Total Memory  field, type the total amount of memory that is now installed.
5. Click  OK.
ENW W Enabling memory 173
 
						

							
Enabling the language-font DIMM for Windows
If the printer has a new language-font DIMM installed, all Windows users of the printer must set the
printer driver to recognize the newly installed font DIMM. Macintosh computers automatically
recognize new language font DIMMs.
1.On the  Start menu, point to  Settings, and click  Printers.
2. Select this printer and select  Properties.
3. On the  Configure  tab, click More.
4. Select the  Font DIMM  check box.
5. Click  OK.
174 Chapter 13   Working with memory ENWW
 
						

							
AAccessories and ordering information
The lists of accessories in this section was current at the time of printing. Ordering information and
availability of the accessories might change during the life of the printer. For the most current
ordering information, visit 
http://www.hp.com .
●
Supplies
●
Memory
●
Cable and interface accessories
●
Paper handling accessories
●
Paper and other print media
●
User-replaceable parts
●
Supplementary Documentation
ENW W 175
 
						

							
Supplies
Product nameDescriptionPart number
Black print cartridgeLife of 2,500 pages at approximately
5% coverage.Q6000A
Cyan print cartridgeLife of 2,000 pages at approximately
5% coverage.Q6001A
Yellow print cartridgeLife of 2,000 pages at approximately
5% coverage.Q6002A
Magenta print cartridgeLife of 2,000 pages at approximately
5% coverage.Q6003A
NOTE
Actual yields may vary according to usage.
176 Appendix A   Accessories and ordering information ENWW
 
						

							
Memory
Product nameDescriptionPart number
Memory upgrades (DIMMs)The standard 64 MB of memory in the
printer can be expanded to up to
192 MB using the additional DIMM slot.
32 MBC7845A
Memory upgrades (DIMMs)64 MBQ1887A
Memory upgrades (DIMMs)128 MBC9121A
Font DIMM (100-pin) You can install an 8 MB language fontROM in the DIMM slot.Visit http://www.hp.com
 for DIMM
availability and ordering.
ENW W Memory 177
 
						

							
Cable and interface accessories
Product nameDescriptionPart number
USB cable 2-meter standard USB-compatibledevice connectorC6518A
178 Appendix A   Accessories and ordering information ENWW