HP CM8060 User Manual

Replace ink cartridges
The device uses four color ink cartridges and one bonding agent cartridge. The bonding agent adheres 
the ink to the paper and improves the durability of the printed output.
A message appears on the control panel whenever a cartridge needs to be replaced. The control-panel
message tells you which cartridge needs to be replaced. 
An ink cartridge expires twelve months after the date of installation if it is installed prior to the install-by
date shown on the ink cartridge package....

3.Push the new cartridge straight in until it locks into place.
4.Please return your genuine HP supplies for recycling to Hewlett-Packard. For more information,
please visit us at 
www.hp.com/go/recycle .
NOTE:On the Supplies Status Page , the HP logo only appears in front of the supply name when
genuine HP supplies are used.
228 Chapter 15   Maintain the device ENWW
 

Replace staple cartridges
NOTE:The HP Multifunction Finisher is an optional a ccessory. Other finishers do not have staplers.
A message appears on the control panel whenever a staple cartridge needs to be replaced. The optional
HP Multifunction Finisher has two staplers. Stapler 1 is on the right, closest to the device. Stapler 2 is
to the left and above Stapler 1. The control-panel message indicates which stapler is empty.
CAUTION:To avoid injury, do not reach into the device to change the staple...

3.To remove the staple cartridge from the cassette, push in at the arrow on each side and then pull 
up to release the cartridge.
4.Insert the new staple cartridge into the staple cassette. Push the cartridge straight down until it
snaps into place.
5.Push the staple cassette straight into the slot.
230 Chapter 15   Maintain the device ENWW
 

6.Rotate the green lever up until it snaps into place.
7.Close the stapler door.
ENWW Replace staple cartridges 231
 

Clean the device
The device does not need to be cleaned often. However, if dirt is visible on the flatbed glass or on the
white-vinyl backing, or if streaks or spots appear in copies, clean the flatbed glass and the white-vinyl
backing. Clean the outside of the device and the touc hscreen periodically to avoid getting dirt on the
flatbed glass and the white-vinyl backing.
Use the following information to clean the device.
Clean the outside of the device
Clean the outside of the device with a soft,...

Clean the flatbed glass
Clean the flatbed glass only if dirt is visible or if streaks or spots
appear in copies.
Gently wipe the glass with a lint-free cloth dampened with
water. Do not pour or spray the water directly onto the glass.
Do not press hard on the glass.
Clean the glass scanner strip
The small glass strip that is to the left of the flatbed glass has
a special coating. Use only gentle pressure when cleaning this
glass strip. Wipe the glass scanner strip with a clean, dry lint-
free cloth....

Move the device
If you need to move the device, contact an HP-authorized service and support person. Special
procedures are required to pr event damage to the device.
234 Chapter 15   Maintain the device ENWW
 

16 Solve problems
This chapter contains information about the following topics:
●
Problem-solving checklists
●
Control-panel messages
●
Clear jams
●
Paper-handling problems
●
Image-quality problems
●
Fax problems
●
Problems with E-mail, Alerts, and AutoSend
●
Problems with sending to a network folder
●
Network-connectivity problems
ENWW 235
 

Problem-solving checklists
If the device is not responding correctly, complete the steps in the following checklists. If you discover
a problem that you cannot resolve, contact  an HP service and support person for help.
Problems with all jobs
1.Make sure at least one status light on the control  panel is lit. If no lights are lit, complete these
steps:
a. Press the on/off button on the control panel.
b. Check the master power switch at the right-rear corner of the device. Make sure it is in the on...