Honeywell 1300g2 Manual

							2 - 15
[
Russia
Russian (MS)
Russian (Typewriter)
SCS
Serbia (Cyrillic)
Serbia (Latin)
Slovakia
Slovakia (QWERTY)
Slovakia (QWERTZ) 
						

							2 - 16
Slovenia
Spain
Spanish variation
Sweden
Switzerland (French)
Switzerland (German)
Tatar
Thailand
Turkey F 
						

							2 - 17
Turkey Q
Ukrainian
United Kingdom
United Stated (Dvorak right)
United States (Dvorak left)
United States (Dvorak)
United States (International)
Uzbek (Cyrillic)
Vietnam 
						

							2 - 18
Keyboard Mode Options
ALT Mode
If your bar code contains special characters from the extended ASCII chart for 
example, an e with an accent grave (è), you will use ALT Mode.  (See Extended 
ASCII Characterson page A-6.)
Note: Scan the ALT mode bar code after scanning the appropriate Keyboard 
Country code.
If your keystrokes require the ALT key and 4 characters, scan the 4 Characters 
bar code.  The data is then output with the special character(s).  Default = Off.
Keyboard Style
This programs keyboard styles, such as Caps Lock and Shift Lock.  Default = 
Regular.
Regular is used when you normally have the Caps Lock key off.
Caps Lock is used when you normally have the Caps Lock key on.
* Off
4 Characters
* Regular
Caps Lock  
						

							2 - 19
Shift Lock is used when you normally have the Shift Lock key on (not common 
to U.S. keyboards).
Automatic Caps Lock is used if you change the Caps Lock key on and off.  
The software tracks and reflects if you have Caps Lock on or off (AT and PS/2 
only).  This selection can only be used with systems that have an LED, which 
notes the Caps Lock status.
Autocaps via NumLock bar code should be scanned in countries (e.g., Ger-
many, France) where the Caps Lock key cannot be used to toggle Caps Lock.  
The NumLock option works similarly to the regular Auotcaps, but uses the Num-
Lock key to retrieve the current state of the Caps Lock.
Emulate External Keyboard should be scanned if you do not have an external 
keyboard (IBM AT or equivalent).
Note: After scanning the Emulate External Keyboard bar code, you must power 
cycle your computer.
Keyboard Modifiers
This modifies special keyboard features, such as CTRL+ ASCII codes.
Control + X (Control + ASCII) Mode On:The scanner sends key combina-
tions for ASCII control characters for values 00-1F.  Windows is the preferred 
mode.  All keyboard country codes are supported.  DOS mode is a legacy 
Shift Lock
Automatic Caps Lock 
Autocaps via NumLock 
Emulate External Keyboard  
						

							2 - 20
mode, and it does not support all keyboard country codes.  New users should 
use the Windows mode.  Refer to Keyboard Function Relationships, page 7-1 
for CTRL+ X Values. 
Windows Mode Prefix/Suffix Off:  The scanner sends key combinations for 
ASCII control characters for values 00-1F (refer to ASCII Conversion Chart 
(Code Page 1252)on page A-3 for non-reprintable characters), but it does not 
translate any prefix or suffix information.
Default = Control + ASCII Off
Windows Mode Control + X  
Mode On 
* Control + X Mode Off 
DOS Mode Control + X Mode 
On 
Windows Mode Prefix/Suffix Off  
						

							2 - 21
Numeric Keypad Mode:Sends numeric characters as if entered from a 
numeric keypad.  Default = Off
Automatic Direct Connect Mode:This selection can be used if you have an 
IBM AT style terminal and the system is dropping characters.  Default = Off
Numeric Keypad Mode On 
* Numeric Keypad Mode Off 
Automatic Direct 
Connect Mode On 
* Automatic Direct Connect 
Mode Off  
						

							2 - 22
RS232 Modifiers
RS-232 Baud Rate
Baud Rate sends the data from the scanner to the terminal at the specified rate.  
The host terminal must be set for the same baud rate as the scanner.  
Default = 38,400.
 300
600
1200
 2400
4800
 9600
19200 
						

							2 - 23
RS-232 Word Length: Data Bits, Stop Bits, and Parity
Data Bits sets the word length at 7 or 8 bits of data per character.  If an applica-
tion requires only ASCII Hex characters 0 through 7F decimal (text, digits, and 
punctuation), select 7 data bits.  For applications which require use of the full 
ASCII set, select 8 data bits per character.  Default = 8.
Stop Bits sets the stop bits at 1 or 2.  Default = 1.
Parity provides a means of checking character bit patterns for validity.
Default = None.
Note: When using 7 Data, 1 Stop, Parity None, the host must insert at least a 1 
bit delay between characters.  If this is not done, a different RS232 Word 
Length format must be used.
* 38400
57,600
115,200
7 Data, 1 Stop, Parity None
(see note above)
7 Data, 1 Stop, Parity Even 
						

							2 - 24
RS-232 Handshaking
RS232 Handshaking allows control of data transmission from the scanner using 
software commands from the host device.   
RTS/CTS Off:  RTS/CTS is turned off so no data flow control is used, but RTS 
is still active.
7 Data, 1 Stop, Parity Odd
7 Data, 2 Stop Parity None
 7 Data, 2 Stop, Parity Even
7 Data, 2 Stop, Parity Odd
  * 8 Data, 1 Stop, Parity None
8 Data, 1 Stop, Parity Even
8 Data, 1 Stop, Parity Odd