Honeywell 1300g2 Manual

							6 - 25
UPC A Number System
The numeric system digit of a U.P.C. symbol is normally transmitted at the 
beginning of the scanned data, but the unit can be programmed so it will not 
transmit it.   Default = On.
UPC A Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC A data.
Default = Off for both 2 Digit and 5 Digit Addenda.
Off *  On
* 5 Digit Addenda Off 5 Digit Addenda On* 2 Digit Addenda Off 2 Digit Addenda On 
						

							6 - 26
UPC A Addenda Required
When Addenda Required is set to on, the scanner will only read UPC A bar 
codes that have addenda.  Default = Not Required.
UPC A Addenda Separator
When this feature is on, there is a space between the data from the bar code 
and the data from the addenda.  When turned off, there is no space.  
Default = On.
*  Not Required Required
Off *  On 
						

							6 - 27
UPC-A/EAN-13
with Extended Coupon Code
Use the following codes to enable or disable UPC-A and EAN-13 with Extended 
Coupon Code.  Default = On.
On
* Off 
						

							6 - 28
UPC E

UPC E0 and UPC E1
Most U.P.C. bar codes lead with the 0 number system.  For these codes, use 
the UPC E0 selection.  If you need to read codes that lead with the 1 number 
system, use the UPC E1 selection.  Default = On (UPC E0) and Off (UPC E1).
*  UPC E0 On
UPC E0 Off
UPC E1 On
* UPC E1 Off 
						

							6 - 29
UPC E0 and UPC E1 Expand
UPC E Expand expands the UPC E code to the 12 digit, UPC A format.  
Default = Off.
UPC E0 and UPC E1 Addenda Required
When Addenda Required is set to on, the scanner will only read UPC E bar 
codes that have addenda.  Default = Not Required.
*  Off On
*  Not Required Required 
						

							6 - 30
UPC E0 and UPC E1 Addenda Separator
When this feature is on, there is a space between the data from the bar code 
and the data from the addenda.  When turned off, there is no space.  
Default = On.
UPC E0 Check Digit
Check Digit specifies whether the check digit should be transmitted at the end 
of the scanned data or not.  Default = On.
Off *  On
Off *  On 
						

							6 - 31
UPC E0 Number System
The numeric system digit of a U.P.C. symbol is normally transmitted at the 
beginning of the scanned data, but the unit can be programmed so it will not 
transmit it.  Default = On.
UPC E0 Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC E data.
Default = Off for both 2 Digit and 5 Digit Addenda.
Off *  On
* 5 Digit Addenda Off 5 Digit Addenda On* 2 Digit Addenda Off 2 Digit Addenda On 
						

							6 - 32
EAN/JAN 13

EAN/JAN 13
EAN/JAN 13 Check Digit
This selection allows you to specify whether the check digit should be transmit-
ted at the end of the scanned data or not.  Default = On.
*  On
Off
Off *  On 
						

							6 - 33
EAN/JAN 13 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 13 data.
Default = Off for both 2 Digit and 5 Digit Addenda.
EAN/JAN 13 Addenda Required
When Addenda Required is set to on, the scanner will only read EAN/JAN 13 
bar codes that have addenda.  Default = Not Required.
* 5 Digit Addenda Off 5 Digit Addenda On* 2 Digit Addenda Off 2 Digit Addenda On
*  Not Required Required 
						

							6 - 34
EAN/JAN 13 Addenda Separator
When this feature is on, there is a space between the data from the bar code 
and the data from the addenda.  When turned off, there is no space.  
Default = On.
Note: If you want to enable or disable EAN13 with Extended Coupon Code, 
refer to UPC-A/EAN-13 with Extended Coupon Codeon page 6-27.
ISBN Translate
This selection causes EAN-13 Bookland symbols to be translated into their 
equivalent ISBN number format. Default = Off.
EAN/JAN 8

Off *  On
*  Off On