Honeywell 1300g2 Manual

							6 - 15
Straight 2 of 5 Industrial (three-bar start/stop)

Straight 2 of 5 Industrial
Straight 2 of 5 Industrial Message Length
Scan the bar codes below to change the message length.  Refer to Message 
Lengthon page 6-2 for additional information.  Minimum and Maximum
lengths = 1-48.  Minimum Default = 4, Maximum Default = 48.
* On
Off
Minimum Message Length
Maximum Message Length 
						

							6 - 16
Straight 2 of 5 IATA (two-bar start/stop)

Straight 2 of 5 IATA
Straight 2 of 5 IATA Message Length
Scan the bar codes below to change the message length.  Refer to Message 
Lengthon page 6-2 for additional information.  Minimum and Maximum
lengths = 1-48.  Minimum Default = 4, Maximum Default = 48.
On
 Off
Minimum Message Length
Maximum Message Length 
						

							6 - 17
Matrix 2 of 5

Matrix 2 of 5
Matrix 2 of 5 Message Length
Scan the bar codes below to change the message length.  Refer to Message 
Lengthon page 6-2 for additional information.  Minimum and Maximum
lengths = 1-80.  Minimum Default = 4, Maximum Default = 80.
On
*  Off
Minimum Message Length
Maximum Message Length 
						

							6 - 18
Code 11

Code 11
Check Digits Required
This option sets whether 1 or 2 check digits are required with Code 11 bar 
codes.  Default = Two Check Digits.
On
*  Off
One Check Digit
*  Two Check Digits 
						

							6 - 19
Code 11 Message Length
Scan the bar codes below to change the message length.  Refer to Message 
Lengthon page 6-2 for additional information.  Minimum and Maximum
lengths = 1-80.   Minimum Default = 4, Maximum Default = 80.
Code 128

Code 128
ISBT 128 Concatenation
In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard  
for communicating critical blood information in a uniform manner.  The use of 
ISBT formats requires a paid license. The ISBT 128 Application Specification 
describes 1) the critical data elements for labeling blood products, 2) the current 
recommendation to use Code 128 due to its high degree of security and its 
Minimum Message Length
Maximum Message Length
* On
Off 
						

							6 - 20
space-efficient design, 3) a variation of Code 128 that supports concatenation 
of neighboring symbols, and 4) the standard layout for bar codes on a blood 
product label.  Use the bar codes below to turn concatenation on or off.  Default 
=Off.
Code 128 Message Length
Scan the bar codes below to change the message length.  Refer to Message 
Lengthon page 6-2 for additional information.  Minimum and Maximum
lengths = 0-80.   Minimum Default = 0, Maximum Default = 80.
Code 128 Code Page
Code pages define the mapping of character codes to characters.  If the data 
received does not display with the proper characters, it may be because the bar 
code being scanned was created using a code page that is different from the 
one the host program is expecting. If this is the case, scan the bar code below, 
select the code page with which the bar codes were created from the chart, 
ASCII Conversion Chart (Code Page 1252), page A-3, and scan the value and 
the Save bar code from the  inside the back cover of this manual.  The data 
characters should then appear properly.
* Off On
Minimum Message Length
Maximum Message Length 
						

							6 - 21
Code 128 Function Code Transmit
By default, Code 128 function codes are not transmitted with Code 128 bar 
code data.  However, if you wish to transmit Code 128 function codes with the 
bar code data, scan the Function Codes On bar code, below.  Default = Off
Te l e p e n

Code 128 Code Page
* Function Codes Off
Function Codes On 
						

							6 - 22
Te l e p e n
Telepen Output
Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1 
and decodes them as standard full ASCII (start/stop pattern 1).  When Original 
Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 
and decodes them as compressed numeric with optional full ASCII (start/stop 
pattern 2).  Default = AIM Telepen Output.
On
*  Off
Original Telepen Output *AIM Telepen Output 
						

							6 - 23
Telepen Message Length
Scan the bar codes below to change the message length.  Refer to Message 
Lengthon page 6-2 for additional information.  Minimum and Maximum
lengths = 1-60.   Minimum Default = 1, Maximum Default = 60.
Minimum Message Length
Maximum Message Length 
						

							6 - 24
UPC A

UPC A
UPC A Check Digit
This selection allows you to specify whether the check digit should be transmit-
ted at the end of the scanned data or not.  Default = On.
*  On
Off
*  On
Off