Honeywell 1202g2 Manual

4 - 9
The following table shows the results of the Auto Reconnect On and Off settings: 
Maximum Link Attempts
The Maximum Link Attempts setting controls the number of times the scanner tries to form a connection with a base.  
During the connection setup process, the scanner transmits in order to search for and connect to a base.  In order to pre-
vent continuous transmissions that could interfere with other users of the ISM band, the number of attempts to connect is 
limited by this setting.  After the...

4 - 10
When the scanner goes out of range, no action is taken to relink.  When  the scanner’s button is pressed, 15 attempts are 
made to link to the base.  Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle 
time.  After 15 cycles (8*15 =120), or about 2 minutes, the scanner stops trying to connect to the base. Refer to Auto 
Reconnect Mode, page 4-8, to review other events that can start the relink process.
Reset Scanner and Base
After changing settings, you...

5 - 1
5
Input/Output Settings
Power Up Beeper
The scanner can be programmed to beep when it’s powered up.  Scan the Off bar code(s) if you don’t want a power up beep.  
Default = Power Up Beeper On - Scanner.
Note: The Voyager 1202g-BF does not issue a power up beep when the scanner is in the base.
Beep on BEL Character
You may wish to force the scanner to beep upon a command sent from the host.  If you scan the following Beep on BEL On bar 
code, the scanner will beep every time a BEL character is...

5 - 2
Beeper Volume – Good Read
The beeper volume codes modify the volume of the beep the scanner emits on a good read.  Default = High.
Beeper Pitch – Good Read
The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read.  Default = Medium.
Beeper - Transmit Order
The beeper transmit order determines when the good read beep occurs.  The scanner can be set to emit the good read 
beep either before or after data transmission.  Default = For Voyager 1200g - Before...

5 - 3
Beeper Pitch – Error
The beeper pitch codes modify the pitch (frequency) of the sound the scanner emits when there is a bad read or error.  
Default = Razz.
Beeper Duration – Good Read
The beeper duration codes modify the length of the beep the scanner emits on a good read.  Default = Normal.
Number of Beeps – Good Read
The number of beeps of a good read can be programmed from 1 - 9.  The same number of beeps will be applied to the 
beeper and LED in response to a good read.  For example, if you...

5 - 4
To change the number of error beeps, scan the following bar code and then scan a digit (1-9) bar code and the Save bar 
code on the Programming Chart inside the back cover of this manual.  Default = 1.
LED Indicators
The green and red LEDs can be programmed to be On or Off and at different brightness levels to indicate various scanner 
states.  Use the following bar codes to program the LED indicators.
LED Settings
Default = For Voyager 1200g - Red LED On with Laser . For Voyager 1202g and 1202g-BF...

5 - 5
LED Brightness
Default = Red High, Green High.
Note: For Voyager 1202g-BF, all LED Brightness settings result in High brightness.
Green LED On when CodeGate 
Disabled
Red LED On when In-Stand
Green LED On when In-Stand
Red LED On with CTS
Green LED On with CTS
Red LED On when Battery is Low
Green LED On when Battery is Low
Red Off
Green Off
Red Low 

5 - 6
In-Stand and Out-Of-Stand Settings
The following settings program the scanner’s behavior when it is either in the stand, or out of the stand (hand-held).  
Caution: When working with In-Stand and Out-of-Stand settings, enable the settings you want before disabling those 
you do not want to use.  If you disable settings first, you may program the scanner so it is unable to read bar 
codes.  if this happens, power cycle the scanner and scan the defaults bar code on page 1-7.
In-Stand and Out-of-Stand...

5 - 7
Presentation Mode with CodeGate Out-of-Stand:  When the scanner is not in the stand, it automatically detects bar 
codes and decodes them.  However, the data is not transmitted until you press the button.  The laser remains on briefly 
after the transmission.  (If you are accustomed to a Voyager 9540, this setting is the same as the 9540’s default.)    
Manual Activation Mode
In Manual Activation Mode, you must press the button to scan a bar code.  The scanner scans until a bar code is read, or...

5 - 8
Manual Activation Laser Timeout - Button Settings
You can set a timeout for the length of time the laser remains on and attempting to decode bar codes when the button is 
held down, and after it is released.  Set the length (in milliseconds) for a timeout by scanning one of the following bar codes, 
then setting the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save.  
Default = Button Hold In-Stand 5000 ms, Button Hold Out-of-Stand 5000 ms, Button...