Honeywell 1202g2 Manual

2 - 31
Communication Timeout
This allows you to set the length (in milliseconds) for a timeout for the host ACK/NAK response.  Scan the bar code below, 
then set the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save.   
Default = 2000 ms.
Communication Timeout 

2 - 32 

3 - 1
3
Cordless System Operation (Voyager 1202g)
Note: This chapter applies only to Voyager 1202g cordless scanning systems.  It does not apply to corded or Voyager 1202g-
BF scanners. See Cordless System Operation (Voyager 1202g-BF) on page 4-1 for Voyager 1202g-BF scanners (PN: 
1202G-BF).
How the Charge and Communications Base Works
A charge and communications base provides the link between the cordless scanner and the host system.  The base contains an 
interface assembly and an RF communication...

3 - 2
When data is scanned, the data is sent to the host system via the base.  The cordless scanner recognizes data acknowledge-
ment (ACK) from the base.  If it cannot be determined that the data has been properly sent to the base, the scanner issues an 
error indication.  You must then check to see if the scanned data was received by the host system.
RF (Radio Frequency) Module Operation
The cordless system uses a two-way Bluetooth® radio utilizing adaptive frequency hopping (AFH) to transmit and...

3 - 3
You will not hear a communication error tone in this mode, but you will hear a short buzz when you press the button if the 
radio communication is not working.  Once the radio connection is made, the scanner produces a series of beeps while the 
data is being transferred to the base.
Page Button
When you press the Page button on the base, the scanner associated with that base will begin beeping (3 short and 1 long 
beep).  If you press the button on a scanner that is beeping in response, or press...

3 - 4
Place the scanner in the base that is connected to an appropriate power supply.  Use only a Listed Limited Power Source 
(LPS) or Class 2 type power supply with output rated 5 to 5.2Vdc, 1A.
Note: If you are powering the base through the interface cable (for example, a USB cable) and not using an external power 
supply plugged into the aux port, the current available for charging is reduced and the charge time is increased. 
Battery Recommendations
 The battery is a lithium ion cell and can be used...

3 - 5
Scanner LED Sequences and Meaning
Note: Pressing the button on the scanner causes the LED to glow red until it communicates successfully with the base. 
Base LED Sequences and Meaning
The base contains a red LED that indicate the status of the unit and verifies its communication with the host system.  The 
base also has a green LED that indicates the scanner battery charge condition. 
Base Power Communication Indicator
To display the power indicator on the base, scan the Base Power Communication...

3 - 6
Reset Scanner
Scanning this bar code reboots the scanner and causes it to relink with the base.
Scanning While in Base Cradle
If you want to be able to scan bar codes while the scanner is in the base, scan the following Scanning in Cradle On bar code.  
If you want to only allow scanning when the scanner is out of the base, scan Scanning in Cradle Off.  Default = Scanning in 
Cradle On.
Note: When Scanning in Cradle Off is selected, the scanner will not scan any bar codes while it is in the base....

3 - 7
Paging
Paging Mode
By default, the paging button on the base pages the scanner associated with that base.  If you want the paging button on 
your base to be disabled, scan the following Paging Mode Off bar code.  When Paging Mode is off, the base will no longer 
page the scanner when the button is pressed.  The red LED on the base will remain lit to indicate that Paging Mode is off.  
(This light will go out when the button is pressed, then back on when it’s released.)  Default = Paging Mode On....

3 - 8
Base Address
Scan the following bar code to determine the address of the base you are using.
Scanner Modes
The Voyager is capable of working with Bluetooth devices other than the  CCB00-010BT base.
Charge Only Mode
There may be times when you want to charge your scanner, but not link to the base.  For example, if a scanner is linked to 
a Bluetooth device and you need to charge the scanner, but want to retain your existing link.  
In order to program the base for Charge Only Mode, you must link a...