Honeywell 1202g2 Manual

5 - 9
CodeGate
When CodeGate is On, the button is used to allow decoded data to be transmitted to the host system.  The scanner 
remains on, scanning and decoding bar codes, but the bar code data is not transmitted until the button is pressed.  When 
CodeGate is Off, bar code data is transmitted when it is decoded.  Default = CodeGate Off in-Stand, CodeGate On Out-of-
Stand.
Button Function
Note: Button Function applies only to the Voyager 1202.  It is not supported in the Voyager 1200.
When Button...

5 - 10
End Object Detection After Good Read
After a bar code is successfully detected and read from the scanner, the laser can be programmed either to remain on and 
scanning, or to turn off.  When End Object Detection After Good Readis enabled, the laser turns off and stops scanning 
after a good read.  If you scan Do Not End Object Detection After Good Read, the laser remains on after a good read.  
Default = End Object Detection After Good Read.
* Object Detection Mode On
In-Stand
* Object Detection...

5 - 11
Object Detection Laser Timeout
You can set a timeout for the length of time the laser remains on and attempting to decode bar codes after an object is 
detected.  Set the length (in milliseconds) for a timeout by scanning the following bar code, then setting the timeout (from 1-
65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save.  Default = 5000 ms.
Object Detection Distance
When you are using Object Detection Mode, you can set the distance range for detecting...

5 - 12
Activation Character
This sets the character used to trigger scanning when using Character Activation Mode.  On the ASCII Conversion Chart 
(Code Page 1252), page A-2, find the hex value that represents the character you want to use to trigger scanning.  Scan 
the following bar code, then use the Programming Chart to read the alphanumeric combination that represents that ASCII 
character.  Scan Save to finish.
End Character Activation After Good Read
After a bar code is successfully detected and...

5 - 13
Deactivation Character
This sets the character used to terminate scanning when using Character Deactivation Mode.  On the ASCII Conversion 
Chart (Code Page 1252), page A-2, find the hex value that represents the character you want to use to terminate scanning.  
Scan the following bar code, then use the Programming Chart to read the alphanumeric combination that represents that 
ASCII character.  Scan Save to finish.
Reread Delay
This sets the time period before the scanner can read the same bar...

5 - 14
Output Sequence Overview
Output Sequence Editor
This programming selection allows you to program the scanner to output data (when scanning more than one symbol) in 
whatever order your application requires, regardless of the order in which the bar codes are scanned.  Reading the Default 
Sequence symbol programs the scanner to the following Universal values.  These are the defaults.  Be certain you want to 
delete or clear all formats before you read the Default Sequence symbol.
Note: If CodeGate...

5 - 15
SEQBLK sequence editor start command
62 code identifier for Code 39
9999 code length that must match for Code 39, 9999 = all lengths
41 start character match for Code 39, 41h = “A”
FF termination string for first code
6A code identifier for Code 128
9999 code length that must match for Code 128, 9999 = all lengths
42 start character match for Code 128, 42h = “B”
FF termination string for second code
69 code identifier for Code 93
9999 code length that must match for Code 93, 9999 = all lengths
43...

5 - 16
Output Sequence Editor   
Sequence Timeout
You may wish to set the maximum time between bar code scans in an output sequence.  If that maximum time is not met, 
the output sequence operation is terminated.  Set the length (in milliseconds) for a timeout by scanning the following bar 
code, then setting the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning 
Save.  Default = 5000 msec.
Sequence Match Beeper
By default, the scanner beeps when a sequence...

5 - 17
Require Output Sequence
When an output sequence is Required, all output data must conform to an edited sequence or the scanner will not transmit 
the output data to the host device.  When it’s On/Not Required, the scanner will attempt to get the output data to conform 
to an edited sequence but, if it cannot, the scanner transmits all output data to the host device as is.
When the output sequence is Off, the bar code data is output to the host as the scanner decodes it.  Default = Off. 
No Read...

5 - 18