GTE Omni Si Database Technical Practices Manual

5210TL-130200-1001
l TIME SLOT TRAFFIC (Transaction D)
i PERIOD 11:30/l 2:001 O/04/87
i
ITIME SLOT TRAFFIC
IPCM BUS
0
1
2
3
4
5
6
7
12:05 8125187USAGE
00000
00000
NOT AVAILABLE
NOT AVAILABLE
00000
00000
00000
00000
I
f
IOVERFLOW 
]
00000IIII
00000II
I
i
00000II
I00000I
I00000 
;
I
00000I
i
f ENTER END (E), REPEAT (R) OR TRANSACTION NUMBER (O-224) >I
I
8187M-95 

TL-130200-1001
l TRUNK GROUP , RLT TRAFFIC (Transaction E)r---‘---“^----‘---‘“----------------------------------------------; PERIOD 11:30/l 2:00 1 O/04/87I
I
iITRUNK GROUP TRAFFIC
I
I12:05 1 O/04/87
. . . .I 
.~_
: TRUNK
I GROUPINCOMING- - - - - - - - - -OUTGOING-,----wm-
i NUMBER CALLSUSAGECALLSUSAGEIATBQVJI
iI02
I03II04II05
I06I
I08
I09I
I10IIRLTI003170040300037
000460009800000
00182
000080007600149
0016900603
000020000000000
0000600002
00001001250013500203
00295
0001700000
00166
00155...

TL-130200-1001
Memory Test3.2.5 Memory Test Results (transaction 34) provides the user
Resultswith a status display of system memory tests. When a memory
failure is detected, the physical location of the faulty cardappears in the error message.
r-------------------------------------------------------------------,I
I
I.=.MEMORY TEST RESULTS34 iII. .I
II
I17:22 09125187I
II
- i PRE-LOAD MEMORY TEST:- FAILURE DETECTED sdrkI
I
I
. .
I
i AT CEC INST MEMORY ADDRESS: 72E6, PAGE: 0, FAULT CODE: 19
I
III
/ CARD...

TL-130200-1001Trunk Sequence3.2.6 Trunk Sequence State Qisplay (transaction 35) provides the
State Displayuser with a plain language description of trunk sequence states.
A CRT display updates the trunk sequence states until
CONTROL-C is entered. Without a CRT, the display is updatedby repeating the transaction. No display will be shown for a trunk
number not in use.
r-------------------------------------------------------------------~
IIREAL-TIME TRUNK SEQUENCE STATE DISPLAY35 I.=.
I1
I
I
. . .
I
I...

TL-130200-1001Data Switch Device3.2.8 The Data Switch Device Status Display (transaction 13)
Status Displayprovides the user with in-service/ out-of-service information
for 
OMNI SI PD-200 Packet Line Cards and Remote
Processors. The user selects transaction A to check the status
of Packet Line Cards, transaction B to check the status of
Remote Processors. or transaction C to exit the menu.
Data Switch Device Status Display
. . .
r-------------------------------------------------------------------~II13...

TL-130200-1001Remote Processors3.2.8.2 Selection of Remote Processors Status (transaction B)
Statusallows the user to monitor the in-service/out-of-service
status of listed PD-200 Remote Processor cards.
c-------------------------------------------------------------------.I
fREMOTE PROCESSORS STATUSI
I
f
TYE
UNIVI
t
IPECGRPSLOTCKTmm--mSTATUS i_--_ - _- - - - -- - - -I--‘----I
I
II
I=- DIFPAINSI
I
-..IIDFPAPMiti
tSPME
;:iINSI
0100sI
I
IAPM:D01iINSI
I
II
I
I-DO YOU WSH TO SEE MORE (Y/N)...

TL-130200-1001Disk Backup3.2.9.1 Selection of the Disk Backup Option (transaction 14)
Optionallows the user to transfer files from the hard disk to the floppy
disk, or from the floppy disk to the hard disk. The system
responds with the following menu:
r-------------------------------------------------------------------,I
IIDISK BACKUPI
I
I
ICURRENT DEVICE ASSIGNMENTS
I
I
I
I
II
I0-10MBYTEDlSK1 - NO DEVICE;I
I
I2 
- 800 K BYTE FLOPPY DISK
3 - NO DEVICE’. .II
I
I4 - NO DEVICE
5 - NO DEVICEI
I
I
I6 
- NO...

TL-130200-1001--Label is used to identify disk if more than one copy
exists
-- Label limited to nine characters
l If a backup floppy disk is wanted type 
“Y “, if not type “N “. A
new disk should be formatted and used for each backup
floppy disk. Use of old disks can affect usable space, and
cause security problems.
-If space runs out on a backup floppy disk, the following
prompt will appear:
FMS ERROR: NOT ENOUGH SPACE ON DISK
- To override this prompt, type a period. The system will
respond:
MOUNT A...

TL-130200-1001
TYPE THE DEVICE IDENTIFIER (0 - 7) >
- DEVICE IDENTIFIER - hard disk, enter 0; floppy disk, enter
2. The system responds with the following directory:
r-----------------------------------------------------------------------------------~I  CATALOG LISTING OF 
S3E$CECODEVICE =10 MBYTE FIXED DISKI
IREC FILERECSI
SECURITY1
IFILE NAMESIZE
SIZEUSEDLAST UPDATED RD 
;WR ---CREATEDI
I
:FM&LABEL016000010000115.04/8616:4415.0418616:440215;...

,TL-130200-I 001
For example, if the response SE is selected, the following file
dump occurs:
FILE: 
XVCECGENI ON 53EBCECODEVICE =10 MBYTE FIXED DISK
RECORD SIZE 
= 512FILESIZE = 01017RECORD USED = 00828
RECO
-.-
. . . .RD #OOOO
000040 7A 01 F4 30000200 0000 00 00 83 02 
D9 B6@ 0
0010
914C 4A 29 91SF0000 0302 00 00 F2 OC 00 00 LJ)
-002000 00 00 00 00000000 0000 SE 06 82 20 00 00 A
003000 00 07 3185050686 0506 86 00 00 00 00 00 1
004000000000000000000003 
1086lF2035 3E5>
00502A-2B21 01 3D...