GTE Omni Si Database Technical Practices Manual

TL-130200-1001FAIII T cnnr n3
.=_POWER DOWN
SYSTEM
R&R EPCMN
FB-J7217 IN Y/O9
(Check Strapping)
POWER UPAND RELOAD
1MONITOR
PSUPY FOR
“ASW” TO LIGHT
I
NOREINSTALL ORIGINAL
EPCMN CARD
1
R&R INCKS IN Y/i 1
(Check Strapping)
POWER UPSYSTEMR&R Ml MB IN 
Y/O2
FB-17213-BOA
(Check Strapping)
1MONITOR
PSUPY FOR
“ASW” TO LIGHT
1
REPLACEBATTERY PACK
FUSE
52108187M-115 

TL-130200-1001Fault Code 07Description:
Disk ErrorBefore loading the system memory from the disk, the systemtests its memory (except common memory). The number of
CRC errors is checked before loading.
Register Data as System Prints:CECO CECO Fault 07 B C D E H L
00 xx 00 00 00 00
TNumber
of CRC
errors
Fault Resolution Steps:
1.Determine number of CRC.errors identified in C register (ifless than 12 errors, disregard fault 07; if more, continue).
::
Reload system -depress reset on PSUPY in P/01.
Monitor...

TL-130200-1001FAULT CODE 07DETERMINE NUMBER
OF CRC ERRORS
(C Register Value)
-
RELOADSYSTEM
1
MONITOR
PSUPY FOR
“ASW” TO LIGHT
YES YESEXCESSIVE CRC EXCESSIVE CRC
IEND
cR&R FMSD IN Y/02
FB-I 7220-BOA
(Check Strapping)
1POWER UP 
&RELOAD SYSTEM
fPOWER DOWN 
&REINSTALL ORIGINAL
FMS CARD
1
R&R FLOPPY
DISK DRIVE
II
52108187M-117 

TL-130200-1001Fault Code 08Description:
Network Test FailureThe system tests the PCM network connecting a time slot to
itself; it then sends a test pattern through the network. This fault
code indicates that a failure has occurred in the PCM network.
Register Data as System Prints:_CECO CECO Fault 08 6 C D E H L
Time
Slot
#
PECFault Type Code:
Number
00= PEC(s) did not respond
(Always 0)02 = Test Failure
Fault Resolution Steps:
1.Power down - turn off main circuit breaker at rear of OMNISI cabinet....

5210TL-130200-1001
FAULT CODE 08
FAULT CODE 08
FB-17218 IN Y/15
AND/OR X/O1
POWER UPSYSTEM
1MONITOR
PSUPY FOR
“ASW” TO LlG.HT
7
R&R EPCMNFB-17217 IN 
Y/O9
(Check Strapping)
1
POWER UPSYSTEM
NOREINSTALL ORIGINAL
R&R 
INCKS IN Y/l 1
(Check Strapping)
POWER UPSYSTEM
1MONITOR
PSUPY FOR
“ASW” TO LIGHT
I
R&R CABLESBETWEEN EPCMN 
&
CHM85 CARDS
i
INO
.IENDl-
8187M-119 

TL-130200-1001Fault Code 09Description:
Directive TestA simulated directive is sent to test the hopper loaders and
Malfunctionunloaders. This fault indicates that the system did not respond
with the correct event.
Register Data as System Prints:CECO CECO Fault 09 B 
C D E H L
“i” O0 Y O0 O0 O0
PEC00 = System did not respond
Numbercorrectly to directive test
(Always 0)03 = System made an invalid
response to the directive
test
Fault Resolution Steps:
1.
2.
3.
4.
5.
6.
7.
a.
9.
10.
11.
12.
ala7Remove...

TL-130200-1001FAULT Cnl3F MlREMOVE BATTERY
PACK FUSE
rPOWER DOWN &
REINSTALL ORIGINAL
CPU85E CARD
I
POWiR DOWN
SYSTEM
II’(WeCk S
I’ IIR&R MPB85 FB-172151
I11
1
R&R 
Ml MB
FB-17314 IN 
Y/O1
(Check Strapping)
4
i-cIN Y/Cl4 & Y/O5POWER UP 
8,(Check Strapping)RELOAD SYSTEM
1
4POWER UP
MONITORSYSTEM
PSUPY FORPOWER UP 
&“ASW” TO LIGHT
1
RELOAD SYSTEM
MONITOR
PSUPY FOR
“ASW” TO LIGHT1 NO
YES
v
ENDA
REPLACE BATTERY
PACK FUSE
52108187M-121 

TL-130200-1001Fault Code 10Description:
Directive Hopper FullThe hopper is tested to ensure that directives are being
Malfunctionunloaded. This fault indicates that the system is failing to unload
its directive.M-l 22
Register Data as System Prints:CECOCECO Fault10 B C D E H L
@f0000000000PEC
Number
(Always 0)
Fault Resolution Steps:
1.
2.
3.
4.
5.
6.
7.
a.
9.
10.
11.
12.
13.Remove battery pack fuse.
Power down 
- turn off main circuit breaker at rear of OMNISI cabinet.
Remove and replace 
MlMB,...

TL-130200-1001
FAULT CODE 10.~.REMOVE BATTERY
PACK FUSEPOWER DOWN
SYSTEM
R&R Ml MB
FB-17314 IN 
Y/O1
(Check Strapping)POWER UP 
&RELOAD SYSTEM
MONITOR
PSUPY FORI“ASW” TO LIGHT
II
cPOWER DOWN 
&REINSTALL ORIGINAL
Ml MB CARD
iR&R 
CPU85EFB-17288 IN 
Y/O4
(Check Strapping)
&POWER UP 
&RELOAD SYSTEM
I4IMONITOR
PSUPY FOR
“ASW” TO LIGHT
REPLACE BATTERY 
1
PACK FUSEPOWER DOWN &
REINSTALL ORIGINAL
CPU85E CARD
POWER UP
.SYSTEM 

TL-130200-I 001Fault Code 11Description:
illegal Event ErrorThis fault is reported when the system receives an illegal value.
MalfunctionThis fault indicates that the system has failed to respond
correctly to a directive.
M-l 24
81875210
Register Data as System Prints:CECO CECO Fault 11 B
CDEH L
PECEventEventEventEventNumber 
ParameterParameterParameter Number
(Always 0) 1
23
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.Fault Resolution Steps:
Remove battery pack fuse.
Power down 
- turn off main circuit...