GTE Omni Si Database Technical Practices Manual

TL-130200-1001
FAULT CODE 19(FAULTCODE1S)REMOVE FUSE
FROM BATTERY
PACK
&POWER DOWN
. .SYSTEM
1
R&R Ml MB IN 
Y/O1
FB-17314
(Check Strapping)
POWER UPAND RELOAD
MONITOR
PSUPY FOR“ASW” TO LIGHT
IYES
INO
T*POWER DOWN &
REINSTALL ORIGINAL
Ml MB CARD
LR&R MPG16 IN 
Y/O2
FB-1721’3
(Check Strapping)
POWER UPAND RELOAD
&MONITOR
PSUPY FOR“ASW” TO LIGHT
REPLACE FUSEIN BATTERY
PACK5210
a/a7M-135 

TL-130200-1001
Fault Code 22Description:MDR SDC FaultAn ambiguous MDR port assignment exists.
M-l 36
Register Data as System Prints:CECO CECO Fault 22 B C D E H L
FF 00 00
PEC
Number
(Always 0)
05= Improper SDC port
assignment
LFault Resolution Steps:
1.Reload system - depress reset on PSUPY card.
2.If terminal records output on port 0, mark MDR port 0 in
service in Table T4551; port 1 must be marked out of
service; back up the data base.
3.If terminal records output on port 1, mark MDR port 1 in
service...

TL-130200-1001
FAULT CODE - 22
FAULT CODE 22
fREGISTER C = 05
RELOAD SYSTEM 
- DEPRESS
“RESET” ON PSUPY IN 
P/O1
1MARK MDR PORT 0 IN SERVICE IN
PORT
YESMARK MDR PORT 1 IN SERVICE IN
NO
ICONNECT THE OUTPUT DEVICEI
LTO THE MDR SCD OUTPUT PORT+(THE PORT WHICH IS NOT
MARKED AS MAINTENANCE)
WARM START THE SYSTEM 
-CYCLE MAIN CIRCUIT BREAKER
AT REAR OF 
St CABINET
IF NO MDR OUTPUT, ASK FOR
ASSISTANCE. NOTE: MDR SDC
PORT TRANSMISSION DATA IS
DERIVED FROM TABLE T6051.
52108187M-137 

TL-130200-1001Fault Code 25Description:
Real-Time Clock FailureThis fault indicates a problem with the Real-Time Clock which is
part of the CPU85 card..
Register Data as System Prints:CECO CECO Fault 25 B C D E H L
\xx/ 00 00 00 00 00
I
00= Clock is out of range
Fl= Read-after-write error
F2= Real time clock problem
Fault Resolution Steps:
1.Power down - turn off main circuit breaker at rear of OMNI
SI cabinet.
2.Remove and replace CPU85E, FB-17288-A‘ in Y/O4
(check strapping).
3.Power up system....

TL-130200-1001. ..--.-v-w --FAULT CODE 25
+POWER DOWN 
SYSTEM.
R&R 
CPU85E
FB-I 7288 IN Y/04
(Check Strapping)POWER UP AND RELOAD
MONITOR PSUPY FOR
“ASW” TO LIGHT
5210
a/a7M-139 

TL-130200-1001Fault Code 27Description:
Disk Backup FailureWhen a power failure occurs, dynamic memory (containing
wake-up, message, etc.) is automatically written to disk topreserve data. This fault indicates that the Hotel/Health Care
dynamic data was not backed up onto the disk.
M-l 40
Register Data as System Prints:CECO CECO Fault 27 B C D E H L
\xx/ xx 00 00 00 00
Y
01= Disk operation failed
02= Disk request failed
00= Disk backup successful
1A= File read failed
1B= File write failed
Fault...

TL-130200-1001
FAULT CODE - 27
IPOWER DOWN SYSTEMI“ASW” TO LIGHT
5210a/a7M-141 

TL-130200-1001 TL-130200-1001Fault Code 30Fault Code 30Description: Description:
Attendant Console Attendant ConsoleCommon transmission to an Attendant Console has failed. Common transmission to an Attendant Console has failed.
Recovery Recovery
Data Check Error Data Check Error
_.Register Data as System Prints:CECO CECO Fault 30 B C D E H L
‘X7’ \x7(/ 00 Yxxy 00 00
Console
0 or 108= Check sum
09= Data linkOA = Timeout occurred
M-142 M-142
81875210 

TL-130200-1001
FAULT CODE - 30
IFAULT CODE 30I
INOTE CONSOLE NUMBER1
REGISTER E = ?
1A, 9, OR 8
ANGLE FAULT h
A”‘- NO ACTION, IGNORE _
1NOATTENDANT
NO ,]I
labREPLACE ATTENDANT CONSOLE
1
YESFORCE ATTENDANT CONSOLE OS
AND REMOVE AND REPLACE THE
ATT12 CARD. FORCE CONSOLE
IN SERVICE.5210
8187M-143 

TL-130200-1001Fault Code 32Description:
CIPNCIPIDVCIP CardThis fault indicates a failure in the CIPNCIPIDVCIP or VP20 card.
FailureM-l 44
Register Data as System Prints:CECO CECO Fault 32 
B C D E H L
y 9 lxp xx xx xxPECCard
NumberNumber
(Always 0) (O-15)
00= Card Test Failure
01= Card XMIT Error
02= Card Watch Dog Timer Error
03= Card Hardware Error
04= Card Initialization Error
Fault Resolution Steps:
1.Identify CIP/VCIP/DVCIP or VP20 relative card number
location by performing a general read of...