GTE Omni Si Database Technical Practices Manual
Here you can view all the pages of manual GTE Omni Si Database Technical Practices Manual. The GTE manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 701
TL-130200-1001 FAULT CODE 11 PACK FUSE FB-17314 IN Y/O1 POWERUP &RELOAD SYSTEM “ASW”TO LIGHTPOWER DOWN &REINSTALL ORIGINAL Ml MB CARD 1R&R CPU85EFB-17288 IN Y/O4 (Check Strapping)REPLACE BATTERY +PACK FUSEPOWER UP &RELOAD SYSTEM 1MONITOR PSUPY FOR “ASW” TO LIGHT IREPLACE BATTERY PACK FUSE 1POWER DOWN &REINSTALL ORIGINAL CPU85E CARD 1R&R MPB85 FB-17215 IN YlO5 & x/O4 (Check Strapping) 11 POWER UP POWER UPSYSTEM SYSTEM 1 1 MONITOR MONITOR PSUPY FOR PSUPY FOR “ASW” TO LIGHT “ASW” TO LIGHT I...
Page 702
TL-130200-1001Fault Code 12Description: Read -After-Write Failure inWhen data is written into channel memory, it is immediately read back and verified. This fault indicates that a failure has occurred Channel Memoryin channel memory. Register Data as System Prints:CECO CECO Fault 12 B C dlfyp++ik PECChannelDataDataNumber Number Written Read (Always 0) (00-5F) JFault Resolution Steps: 1.Power down - turn off main circuit breaker at rear of OMNI St cabinet. 2.Remove and replace CHM85, FB-17218-A, in X/O1...
Page 703
TL-130200-1001 FAULT CODE 12 FAULT CODE 121POWER DOWN SYSTEM POWER UPSYSTEM I1IMONITOR PSUPY FOR “ASW” TO LIGHT YES NOPOWER DOWN &REINSTALL ORIGINAL CHM85 CARD 1REMOVE FUSE FROM BATTERY PACK I1IR&R Ml MB FB-17213-BOA IN Y/O2 (Check Strapping)1 POWER UP &RELOAD SYSTEM 1I+MONITOR PSUPY FOR “ASW” TO LIGHT 1 REPLACE FUSE INBATTERY PACK 5210 8f87M-127
Page 704
TL-130200-1001Fault Code 15Description: Tl AlarmThe system monitors the TlS (Tl Supervision Circuit Card) for hardware alarms. This fault indicates that the data framing of a span has failed for 36 ms, the power has failed in the local office terminating equipment, or synchronization has been lost at the distant office for 1.2 seconds. M-l 28 Register Data as System Prints:CECOCECO Fault15 B C D E H L 2 00 py 0; 00 00 Alarm Number Number 00= System Alarm (Always 0) 01= Remote Alarm 02= Cutoff Alarm 03=...
Page 705
TL-130200-1001EAI IIT1 EFAULT CODE 15 11 YESREMAIN LIT? OBSERVE FRONT OFREMAINS LIT? . .Tl S FB-20718 SYS LAMP LIT INDICATES ANY ALARM CONDITION EXISTS R&RSEQUENTIALLY ALL TlCARDS UNTIL FAULT IS Cl FA.RFnI“LL, I. .LY I & ENDLOC LAMP LIT & D REGISTER,-II4 RPF LAMPLIT & D REGISTER>^ cYES II LYES5210 8l87M-129
Page 706
TL-130200-1001Fault Code 16Description: 10 ms Stopped FailureThe system performs checks to ensure that the 10 ms interrupt is operating. A time check is performed to see if the background scheduler has been interrupted to perform foreground scheduler tasks. If the average time is too short, it is assumed that the interrupt is not operating. M-130 8187 i RegisterDataasSystemPrints:CECOCECO Fault16 6 C D E H L 000000000000 Fault Resolution Steps: 1.Power down - turn off main circuit breaker at rear of...
Page 707
TL-130200-1001 FAULT CODE 16 FAULT CODE 16 POWER DOWNIR&R CPU85EFB-17288 IN Y/04 (Check Strapping) POWER UPAND RELOAD MONITOR PSUPY FOR“ASW” TO LIGHT 5210 M-131
Page 708
TL-130200-1001Fault Code 17Description: Alarm FaultThis fault indicates that a fault has been detected in a Tl span or the alarm relays have been pulled on the ATT12 card. M-l 32 Register Data as System Prints:CECO CECO Fault17 B C D E H L xx 00 00 00 00 “i” TAttendant 00 = ATT12 card has failedConsole 01= Fault on Tl span Oor 1 09= Attendant 0 transmission fault OA= Attendant 1 transmission fault Fault Resolution Steps: 1.If C register value is 00, 09, or OA, complete the following steps: - Identify...
Page 709
TL-130200-1001 FAULT CODE 17 FAULT CODE 17 IDENTIFYCONSOLE/ATT1 2CARD VIA T2621 IGO TO FIWLTCODE15TROUBL ---.ESHOOTING PRCCEDUREI FORCE CONSOLE00s 1 R&R ATT1 2 FB-17208 (Check Strapping) 1 FORCE CONSOLE IN-SERVICE. R&R ATTENDANT I CONSOLE I END I45210 II 8l87M-133
Page 710
TL-130200-1001Fault Code 19Description: Pre-Loading MemoryBefore the contents of the disk are loaded into the system Failure Testmemory, all eight pages of the RAM are tested and any error is detected. This fault indicates that there is a failure in the RAM memory card. Register Data as System Prints:CECOCECO Fault19 6 C D E H L P 00 00 00xx xx -T-Address of Failing Byte Failing Software Paae: 00=instructionPage0 01=InstructionPage1 02=Data Page0 03=Data Page 1 04=InstructionPage2 05=InstructionPage 3...