GTE Omni Si Database Technical Practices Manual

REGLINE#CONTENTS (10 COUNTERS PER LINE)
~~~L~RK030 TGOOTGOlTG02TG03TG04
TG05TG06TG07TG08TG09031 
TGlOTGllTG12
TG13TG14
TG15TG16TG17TG18TG19032 TG20
TG21TG22
TG23TG24
TG25TG26TG27TG28TG29033 TG30
TG31TG32TG33TG34
TG35TG36TG37
TG38TG39034 TG40
TG41TG42
TG43TG44
TG45TG46TG47
TG48TG49035 TG50
TG51TG52
TG53TG54
TG55TG56TG57
TG58TG59.~_036 TG60
TG61TG62-i-G63 __-_ ____ ____ ____ ____RLT. . .
EGTERK037 TGOOTGOlTG02
TG03TG04TG05
TG06TG07
TG08TG09038 
TGlOTGllTG12TG13TG14TGl5TG16TG17
TG18TG19039 
TG20.TG21...

Table 2.2Traffic Data Commands Input and Output Formats
INPUT FORMATTD DT.- to display the date and time of
dayTD DT 
xx/yy/zz nn:nn - to change the
time-of-day clock.
TD BS. 
- to-begin a traffic study--TD ES.- to end a traffic study
where
xx = the month
YY= the day of the month
zz =the last two digits of the year
nn:nn =the time of day in hours and
minutes in 24-hour format
M-48
8187
OUTPUT FORMAT
xxIyy/zz nn : nn
DT 
xx/yy/zz nn : nn ? EXECUTED
BS site xx/yy/zz nn/nn aa bbb
cccc dddd/eeee/: Y....

5210FTM 0184The following information is being supplied to clarify the operation
of the traffic data facilities on the 
OMNI SI in areas of:
l All trunks busy
l Overflow
l Usage
ATB (lines 41-47 in traffic layout) 
- Pegging occurs each time
the last available trunk (defined as the last trunk in the idle trunk
state) is changed from idle to any other trunk state. It is valid to
have ATB pegged for an incoming only trunk group, an outgoing
only trunk group,. or for a 2-way trunk group.
OVF (lines 48-54 in...

TL-1 3Uzuu-I UUI
Display Command2.1.7 The display command (Line, Trunk, Call State) is used to
list the addresses and data of the tables listed below:
l T4170Line State Table. T4160
Line Call Store Link Table. T8941
Trunk State Table. T8944
Trunk Call Store Link Table. T1390
Call Store TableThis information is used in call tracing and is shown in section
6.0.The formats of the display commands are shown in Table 2.3.
M-5081875210 

Table 2.3
Display Command Input and Output Formats
Iisplay Line State:
DISPLAY LINE DN STATEoutput
PAGEADDRESSDATA_--__-_ .2--_----_-_____- - _ - - -- - -
._..xxYYYY
zz
tvhererXX = page ID (DO, D2, D3, D4, D5,06, D7)
._YYYY = address of line state
ZZ = present state (see Table 2.4 for CEC Line State Codes)
display Line Call Store Link:Input
Input
DISPLAY LINE DN CSLINK
OutPut
PAGEADDRESSCS#PAGECS ADDR RANGE---m--v-m------m-__-------------__--_---_--____---_______xx
YYYYzzAABBBB-CCCC
Nhere:XX = page of...

Table 2.3 Display Command Input and Output Formats (Continued)Display Trunk State:
Input
DISPLAY TRUNK STATE
where:
 
.= system trunk number in decimal (O-63).
=-Output
PAGE
ADDRESSDATA
-------
-------------
---_-----xx 
-YYYY22where:
XX = page ID (DO, 
D2,03, D4, D5,06, D7)YYYY = address of trunk state
ZZ 
= present trunk state (see Table 2.5 for CEC Trunk State Codes)
Display Trunk Call Store Link:
Input
DISPLAY TRUNK CSLINKOutput
PAGE
ADDRESSCS#PAGECSADDR RANGE-- - - -...

.bI”“-“” .““.
Table 2.3Display Format (Continued)
Display Call Store Address:
,lnput
DISPLAY CSADDRESSwhere:
 =call store number in decimal
output--..PAGECS ADDR RANGE..----------------_--------------
- xxBBBB-CCCCwhere:XX 
= page lD(D0, Dl, D2, D3, D4, D5, D6, D7)BBBB 
= start address of call store
CCCC 
= end address of call store
Table 2.4CEC Line State Codes
CODELINE STATE
ILine idle1 Line ringing
02Line busy
03Line digit collection
04Call-back in progress
05Call-back ringing
06Line locked out
07Line...

Table 2.5CEC Trunk State CodesM-54
CODETRUNK STATE
01Incoming pre-seized trunk
02Incoming mishandled trunk
03Incoming FX trunk wait for resources
04Incoming not answered (idle)
05incoming loop not answered (idle)
06Incoming busy (idle)
97.
08Incoming signaling A
Incoming signaling 8I
09) Incoming dialing (idle)1
OA08Incoming delay dial wait
Outgoing start dial wait
ocIOutgoing wink start wait
OD
OEOutgoing busy (idle)
Outgoing guard after release
OF
10Outgoing immediate dial
Outgoing glare check
Recorder...

.-.----- .--.
Table 2.5CEC Trunk State Codes (Continued)
CODETRUNK STATE
1E
I1 Maintenance busy
1FSystem busy
20Incoming not answered (busy)
21_.1 Incoming loop not answered (busy)I
. . . .22Incoming busy (busy)
23incoming dialing
24 
.*
25Incoming dialing (busy)
Recorder Announcer start
26Recorder Announcer message cycle
27Call recovery trunk off-hook
28CAS Main ACD recorded announcement start
I
291 CAS Main ACD recorded message cycleI2ANailed connection
Maintenance Commands2.2 Maintenance commands are...

Software IdentityFor initial installations, the SID number for lines or trunks can be
Calculationsfound in the Cable Pair Listing - Table in TL-130400-1001
Use the decimal listing under each line or trunk number.
1. To calculate the SID for lines use 
R C Table 221 and the
following calculation:
__SID =RC Table 221 primary identifier x 8 + circuit number; or
SID =Line card’s position number in the Line Card Address
Table T2541 x 8 + the circuit number; where:
VCIP, DVCIP, VPLC (types VPLO and 
VPLl), and...