GTE Omni Si Database Technical Practices Manual

5210- .----- .--.
Force In Service2.2.1 The FORCE command can be used to force
Out of Service
Commanddevices and/or circuits into the maintenance busy state
when not idle. Removing a device from service using the
FORCE command takes the device down unconditionally.
Featurephones2.2.1.1 To force an Analog or Digital Featurephone connected to
a CIP, DCIP, or DVCIP port in service .or out of service, enter the
following:
-------------------------------------------------------,
IS.I
IFORCE CIP DN I
I
OS.I...

.- .__--- .--To force a Digital Featurephone, with voice application only,
connected to a VPLC2 (type 
VP20) port out of service, enter the
command given below:
~-------------------------------------------------------.I
I
I
IS. ;I
IFORCE DN 
C directory-no, >I
OS. ior
I
II
IFORCE DIFP    I
I
OS. ;I
I
-I whereI
II
III/  
< directory-no, >= three- or four-digit directory numberI
II
I
of a Featurephone
II  
 = 0I
II  
= AtoDIIi  
= 
oto11II:  
= oto7I
II...

5210.- .-“-WV .--.
Line Cards with2.2.1.2 To force a CIP, VCIP, or DVCIP interface card in
Featurephonesservice, enter the following:
I -------em ------------------------------------------------------,IIIIS.IIFORCE CIP CARD < pet > I
I
I
I
I
I
OS.II
I
I
I
; whereI
I
,
I
II..-;  = 0
;  = 0 to 15
To force the VPLC2 (type VP20 or VP21) card out of service,
enter the command given below. This command causes all
ports on the card to be placed out of service regardless of port
type (voice, data, or voice and...

M-60To force a trunk circuit from active to maintenance busy suing
the SID, enter the following:
I-----‘----‘--------‘-------------’---------------------------------,II
i FORCE TRUNK SID  
I
OS.I
I
III
; whereI
;  = 0I
I
; = Trunk circuit SID relative to the PEC: 0 to 63II
II
__r-----,----,-------_,-___L-__,-___,____-------------------------J
Attehdant and Busy2.2.1.4 To force an Attendant Console in service or out of
Lamp Display Unitservice, enter the following:...

Force Download and2.2.1.6 Certain devices in the system require downloading
Load Commandssoftware from the disk into remote processors. These devices
are:
52101. Digital Integrated Featurephone (DIFP)
2. Digital Integrated Featurephone with Data Option (DFPAPM)3. 
VCIP and DVCIP cards
4. Asynchronous Packet Manager (APM)
5. Synchronous Packet Manager (SPM)
6. VPLC2 card (type VP20 or VP21)
7. Universal Controller Board (UCB) DCP and NIC cards
8. ADMP cardThe force download command is used to load...

The format of the force download command is as follows:r---------------------------------------------------I-Ij  FORCE DOWNLOAD 
C pet > < sid > .
I
I
I
II
or
II
I  FORCE DOWNLOAD DN 
C directory-number >I
II
III;  whereI
II
IIII  
Cpec> = 0II  
 =
Software ID (SID) of a featurephone toIII
Idownload (0 to 225).III  
< directory-number > =three-or four-digit directoryI
II
number of the featurephon to be downloaded.
IIII
/  FORCE DOWNLOAD 
  INTERFACE
I
iIIIII  whereI
II
I
I
I
I  
Cpec> = 0I
II  
 =...

NOTES:1. When a download to a card is completed, each of the
individual Digital Featurephones plugged into the card is
downloaded with data unique to the Digital Featurephone.
2. Download to a 
VCIP or DVCIP card puts all ports on the card
out of service until the download is complete.
3. For LOAD 
DIFP ALL command, the PEC number is appended
to the response message.
.=_The following paragraphs provide guidelines and sample sue of
these commands.
. . .
Downloading2.2.1.7 Several versions of the force...

- .--- -- .--.
----------------------------------------------------,ILOAD DN 
< directory number >
I.I
IM-64
81875210 

I I-- IduLuu- I vu I
Downloading VCIP,2.2.1.8 To download software into the VCIP, DVCIP, or VPLC
DVCIP, and VPLC Cardscard, use the following command:
r--‘-------------------------------------------------,II
j FORCE DOWNLOAD < pet > < sid > INTERFACEI
II
III;  where
I;  
Cpec> = 0I;  
= Software ID of a Digital Featurephone pluggedi
1 _ i_nto the card (0 to 225).I
- - ------____--------------------------------------:To download software into the VPLC2 (type VP20 or VP21) card,
use the following command:...

.- .----v .w...
Downloading ADMP,2.2.1.9 To download the ADMP, UCB.(DCP), and NIC card, use
UCB (DCP),andthe following command:
NIC Card
. . .
r-----------------------------------------------------IIIII  LOAD  
   OP>I
II
IIII
I  whereI
II
IIII  = ADMP, DCP, NICI
II  
 = 0I
I1  
 = AtoDI
I
I. .I  = oto11I-----_--------------________--------------------------------~
Bulk Downloading2.2.1.10 Several bulk downloading commands have been
Commandsprovided for situations in which all circuits and/or cards need...