GTE Omni Scbs Installation And Maintenance Manual

Review Exercise - Special System 
Configurations 
(2.11) (Co nued) 
GE 
OhMNU SBCS 
4. THE SYSTEM WILL ALLOW A MAXIMUM OF 
TENANT GROUPS FOR SiATlONS AND 
TRUNKS. 
5. WHAT PROGRAMMING WOULD BE REQUIRED TO ALLOW TENANTS TO HAVE THEIR OWN 
INCOMING AND OUTGOING TRUNKS? 
6. WHAT ADDITIONAL CUSTOMER PROVIDED EQUIPMENT IS REQUIRED FOR OPX 
INSTALLATION? WHY? 
7. WHAT PROCEDURE(S) COULD BE USED TO CHANGE THE DEFAULT STANDARD RINGING PATTERN 
FOR AN OPX STATION? 
8. OPX STATIONS INTERFACE TO THE OMNI SBCS...

Review Exercise - Special System 
Configurations (2.11) (Coutinued) 
9. WHAT PARAMETER AND SETTING IS REQUIRED FOR CMC-204 FOR DESIGNATING AN OPX 
STATION? 
10. MATCH EACH OF THE FOLLOWING CMC COMMANDS WITH ITS CORRECT DEFINITION: 
CMC-100 
CMC-102 
CMC-200 
CMC-201 
CMC-204 
CMC-251 
CMC-254 
CMC-400 
CMC-503 A. 
TRUNK DIALING GROUP AND RESTRICTION GROUP ASSIGNMENT 
B. 
TRUNK DATA ASSIGNMENT 
C. 
SYSTEM PARAMETER ASSIGNMENT 
D. DATA SECURITY AND OPX ASSIGNMENT 
E. TRUNK GROUP ROUTE TIMING ASSIGNMENT 
F....

Save/Load Procedures 
2.208  

2.12 Enabling Objective 
GIVEN: . GTE OMNI SBCS 
. GTE OMNI SBCS PERIPHERALS 
. PORTABLE MAINTENANCE PANEL 
. GTE OMNI SBCS COURSE AND SITE DOCUMENTATION PACKAGE 
. LABORATORY ACTIVITY - SAVING AND LOADING OFFICE DEPENDENT 
DATA BASE ODDB) 
. REVIEW EXERCISE 
ACTION: . USE OMNI SBCS PROGRAMMING TOOLS AND EQUIPMENT TO: 
- SAVE OFFICE DEPENDENT DATA BASE TO TAPE. 
- LOAD OFFICE DEPENDENT DATA BASE FROM TAPE. 
- SAVE OFFICE DEPENDENT DATA BASE TO FLOPPY DISKETTE. 
- LOAD OFFICE DEPENDENT DATA BASE FROM...

-. ,- 
. . . __ 
Office Dependent 
ase to Tape 
1 DESCRIPTION 1 
@ AFTER PROGRAMMING CHANGES, CUSTOMIZED DATA BASE OR OFFICE DEPENDENT DATA BASE 
(ODDB) STORED IN THE OMNI SBCS SYSTEM MAIN MEMORY MUST BE STORED TO A PMP 
MICROCASSETTE. 
. TIME REQUIRED TO WRITE ODDB TO TAPE IS DEPENDENT UPON SIZE OF ODDB AND LINE SPEED. 
. SAVE PROCEDURE WILL NOT INTERRUPT CALL PROCESSING IF OPERATING AT LESS THAN 1200 
BITS PER SECOND. 
@ SAVE PROCEDURE CANNOT BE PERFORMED USING MASTER CONTROL TELEPHONE. 
1 PROCEDURE 1...

Saving Office Data I3ase 
to Tape (Continued) 
e. THEN SCREEN WILL DISPLAY TAPE DATE INCLUDING SAVED DATE, TAPE VERSION, AND VOLUME SERIAL NUMBER: 
*SAVE PROCESS 
SAVEODATENNIDDIY 
TAPE VER xxx/VOL XY 
f. WHEN SAVE PROCESS IS COMPLETED, THE SCREEN WILL DISPLAY: 
n 
*SAVE PROCESS 
COMPLETION 
c ERRORS / 
. IF ODDB BACKUP TAPE HAS NOT BEEN INSERTED OR IF TAPE IS OVERWRITE PROTECTED, SCREEN WILL DISPLAY: 
*SAVE PROCESS 
r-l 
TAPE DOES NOT EXIST 
SEEDATATAPE 
HIT PF9 TO START 
INSERT TAPE OR BREAK OVERWRITE...

Saving Office Data Base 
Tane (Co tinued) 
m . 
. IF RELEASE (PFI) KEY IS ACCIDENTALLY PRESSED, SAVE PROCESS WlLL BE INTERRUPTED AND’ 
SCREEN WILL DISPLAY: 
*SAVE PROCESS 
QUIT 
BEGIN SAVE PROCEDURE AGAIN FROM STEP a. 
2.212  

Loading Office Dependent 
Data Base From Tape 
DESCRIPTION 
@ TIME REQUIRED TO LOAD ODDB FROM TAPE IS DEPENDENT UPON SIZE OF ODDB AND LINE 
SPEED. 
@ ALL CALL PROCESSING STOPS DURING LOADING PROCESS. 
. AFTER COMPLETION OF LOADING PROCESS, OMNI SBCS AUTOMATICALLY INITIATES HOT 
RESTART. 
1 PROCEDURE 1 
NOTE: BECAUSE CALL PROCESSING STOPS DURING LOADING PROCESS, CHECK CALL STATUS 
WITH DSS/BLF CONSOLE AND WAIT UNTIL CALLS ARE COMPLETED. IF LOADING RE- 
QUIREMENT IS URGENT, INTERRUPT CALLS THROUGH...

Loading Dependent Data Base 
ntinu.ed) 
d. PRESS PF9 (SHIFT -t PF4). CALL PROCESSING NOW IS INTERRUPTED. SCREENI WILL DISPLAY: 
f 1 
*mm PROCESS 
START 
I-J 
THEN SCREEN WILL DISPLAY TAPE DATA INCLUDING SAVED DATE, TAPE VERSION, AND VOLUME 
SERIAL NUMBER: 
e. PRESS PF9 (SHIFT + PF4) TO START LOADING PROCESS. 
f. WHEN LOAD PROCESS IS COMPLETED, THE SYSTEM WILL AUTOMATICALLY INITIATE A HOT 
RESTART. THE SCREEN WILL DISPLAY: 
f I 
- 
9 CONFIRM HOT RESTART BY VERIFYING THAT “%ECtitii?Y CODE=” IS DISPLAYED ON...

Loading Office ependent Data Base 
From Tape’N(Continued) 
GTL aiM#Nn SBCS 
ERRORS 
. IF ODDB TAPE VERSION DOES NOT MATCH OMNI SBCS SOFTWARE VERSION,, THE SCREEN 
WILL DISPLAY: 
CHANGE TAPE AND 
PRESS PF9 (SHIFT + PF4). REPEAT STEP D AND CONTINUE1 PROCEDURE. 
e IF INSERTED TAPE IS NOT ODDB TAPE, THE SCREEN WILL DISPLAY: 
f 1 
CHANGE TAPE AND PRESS PF9 (SHIFT + PF4). REPEAT STEP D AND CONTINUE PROCEDURE. 
. IF ODDB TAPE VOLUME SERIAL NUMBER IS NOT CORRECT, THE SCREEN WILL DISPLAY: 
/ 3 
L J 
CHANGE TAPE...