GTE Omni Scbs Installation And Maintenance Manual

,I., . 
‘. 
3.20  

Software and Distributed Processor 
Version Number Displays 
i DESCRIPTION 1 GTE aww a3cs 1 
1 
@ CMC-904 WILL DlSPLAY CURRENT SYSTEM SOFTWARE VERSION’ 
NUMBER INDICATING: 
- FEATURE PACKAGE BY ALPHABETIC CHARACTER 
- SAVE/LOAD OPERATION CAPABILITY 
- RELEASE VERSION WITH ENHANCEMENTS AFFECTING 
DOCUMENTATION, TECHNICAL OR SALES TRAINING. 
- POINT RELEASE VERSION WITH ENHANCEMENTS NOT AFFECTING 
USER OPERATION 
. CMC-907 WILL DISPLAY CURRENT DISTRI,BUTED PROCESSOR 
VERSION NUMBER FOR ANY CARD IN...

Ssfkware and Distributed Braces 
r&ion N 
2. USE CMC-907 TO OBTAIN CURRENT VERSlON NUMBER FOR lNTERFACE 
CARD. ENTER 
DISPLAY AT Pl: 
. EQUIPMENT NUMBER (PI) 
. CARD TYPE (P2) 
1: 8SLC 
2: 4BWC 
3: 2TTE 
CMC=907 
Pl: 040 
cl 
P2: 1 
P3: 0 
4: 2TTL 
5: 4DMR 
. VERSION NUMBER (P3) 
NOTE: WHEN THE CARD FOR SPECIFIED EQUIPMENT NUMBER IS NOT 
INSTALLED OR IS AN 8EKC OR 8DTC CARD, THE CARD TYPE 
AND VERSION NUMBER CORRESPONDING TO THE NEXT 
CARD (EXCEPT FOR 8EKC OR 8DTC) ARE DISPLAYED. 
3.22  

Device Status Display 
1 DESCRIPTION 1 
o CMC-800 iDISPLAYS A SERIES OF THREE SCREENS BRIEFLY LISTING FAULTY DEVICES AND 
LOCATIONS. MORE DETAILED INFORMATION ABOUT THESE FAULTS CAN BE OBTAINED WITH 
CMC-801. 
l FOLLOWING ABBREVIATIONS FOR FAULTY DEVICES MAY BE LISTED: 
DEVICE ABBREVIATION 
DEVICE NAME 
cc 
RAM 
RTS 
BAT 
swc 
ICG 
TRM 
SCI 
RG CPM CARD OR MEM CARD 
RAM ON CPM CARD OR MEM CARD 
REAL TIME SOURCE ON CPM CARD 
BATTERY 
SWC CARD 
TRUNK/LINE CARD 
ELECTRONIC KEY TELEPHONE INSTRUMENT 
RS-232-C...

pii5Gcq 
1. ENTER CMC-800. AT PI, PRESS 
DBSPLAY TO DISPLAY SCREEN ONE. 
GTE aww SBCS 
CMC=800 DSP 
cl 
::; ICG TRM 
P3: 
2. AT PI, PRESS DISPLAY TO DISPLAY 
SCREEN TWO*: r  
CMC=800 DSP 
Pl: ICG&SCI STATUS 
P2: 0000000000 
P3: 000000100 00 
3. AT PI, PRESS DISPLAY TO DISPLAY 
AT SCREEN THREE*: 
CMC=800 DSP 
Pl : FAULT TERMINAL 
4. IF hi0 OTHER INFORMATION IS 
AVAILABLE, SCREENS ARE 
SKIPPED AND END IS DISPLAYED). 
METER VALUES ARE DESCRIBED IN 0 NI SBCS GTEP MANUAL, 
(MAINTENANCE SECTION, CMC-800). 
3.24  

Fault Log Display 
1 DESCRIPTION 1 
0 PROVIDES DETAILED FAULT INFORMATION FOR TROUBLE-SHOOTING 
INCLUDING: 
- DEVICE NAME AND EQUIPMENT NUMBER 
- TIME OF FAULT OCCURRENCE OR REPAIR 
- CAUSED FACTOR AND SUPPLEMENTARY FAULT DATA 
READING OUT FAULT LOG TURNS THE ALARM AND TIMER OVERFLOW 
LAMPS OFF AND INITIALIZES THE WATCH DOG TIMER RESTART 
COUNTER TO ZERO. 
FAULT INFORMATjON IS DISPLAYED IN HISTORICAL ORDER OF 
OCCURRENCE WITH MOST RECENT FAULT DISPLAYED LAST. 
MAXIMUM OF 16 FAULTS IS STORED. WHEN NUMBER...

d  Fault Log Display (Continued) 
1 PROCEDURE 1 
1. 
2. 
3. ENTER CMC-801. AT PI PRESS 
DISPLAY TO DISPLAY OLDEST 
FAULT LISTING IN LOG: 
CONTINUED TO PRESS 
DISPLAY AT 
Pl UNTIL ALL FAULTS LISTED IN 
LOG HAVE BEEN DISPLAYED: 
AFTER ALL FAULTS HAVE BEEN LISTED 
FROM LOG, END IS DISPLAYED: 
3.26 CMC=801 DSP 
PI: TRM P4: 026 
P2: 11: 22 02/28 
P3: 0 
c 
CMC=801 DSP 
Pl: TRM P4: 005 
P2: 12:16 02/03 
P3: 1 
I 
CMC= END 
cl  

NAME DEVICE OR 
EQUIPMENT 
NUMBER (P4) CdUSED 
FACTOR (P3) 
FAULT DATA (P4) (SEE NEXT PAGE) 
&MCARDOR MEM CARD 200 OR 
0 - COLD RESTART 
210 
1 = WATCH DOG TIMER OVER-FLOW 
2 : SOFTWARE MAZE 
3 = RAM DATA PROBLEM 
4 - ILLEGAL INTERRUPTION 
5 MANUALHOT RESTART 
RAM 
RAM ON CPM OR 
MEM CARD 
RTS 
REAL TIME SOURCE 
ON CPM CARD 
BAT 
BATTERY 
swc 
SWC CARD 
ICG 
TRUNK/LINE CARD 
TRM 
PROPRIETARY 
TELEPHONE 
SCI RS-232-C PORl 200 
2 ILLEGAL TIME 
FIRST EN 
ON CARD 
EN OF 
EKT OR 
DSS 
PORT NO 
000/001 0 =...

Fault Log Display (Continued) 
1 PROCEDURE 1 
1. 
2. 
3. ENTER CMC-801. AT PI PRESS 
DISPLAY TO DISPLAY OLDEST 
FAULT LISTING IN LOG: 
CONTINUED TO PRESS 
DISPLAY AT 
Pl UNTIL ALL FAULTS LISTED IN 
LOG HAVE BEEN DISPLAYED: 
AFTER ALL FAULTS HAVE BEEN LISTED 
FROM LOG, END IS DISPLAYED: 
CMC=801 DSP 
Pl: TRM P4: 026 
P2: 11: 22 02/28 
P3: 0 
I 
CMC=801 DSP 
Pl: TRM P4: 005 
P2: 12:16 02/03 
P3: 1 
CMC= END 
. 
3.26  

CMC-801: DE”,CE 
NAME DEVICE OR 
EQUIPMENT 
NUMBER (P4) 
200 OR 
210 
CiUSED 
FACTOR (Pa) 
0 - COLD RESTART 
1 = WATCH DOG TIMER OVER-FLOW 
2 SOFTWARE MAZE 
3 .- RAM DATA PROBLEM 
4 - ILLEGAL INTERRUPTION 
5 MANUAL HOT RESTART 
FAULT DATA (P4) (SEE NEXT PAGE) 
RAM 
RAM ON CPM OR 
MEM CARD 0 : TURN ALM LAMP OFF 
1 - RAM MEMORY STACK 
2 RAM PROTECTION 
RTS 
REAL TIME SOURCE 
ON CPM CARD 
BAT 
BATTERY 
swc SWC CARD 
ICG 
TRUNK/LINE CARD 
TRM 
PROPRIETARY 
TELEPHONE 
SCI 
RS-232-C PORT 
ZEN CARD 200 
2...