GTE Omni Scbs Installation And Maintenance Manual

Fault Code Translation (Continued) 
Gull OMNi SBGS 
CIVIC-801 : 
FAULT DATA TRANSLATION 
1. FAULT DATA IN HEX CODE: 
HH HH HH HH HH HH HH 
1 234567 
H: HEX CHARACTER O-9, A TO F OR BLANK 
2. SCI STATUS 
EACH BIT SHOWS THE FOLLOWING MEANING: 
BBBBBBBB 
l- 
L 
!: L 
TRANSMITTER READY 
RECEIVER READY 
TRANSMITTER EMPTY 
PARITY ERROR 
OVER-RUN ERROR 
FRAMING ERROR 
BREAK DETECT 
DATA SET READY 
3.28  

DESCRIPTION 
0 PLACE SMDR PRINTER OUT OF SERVICE WITH CMC-705 WHEN CHANGING 
PAPER. ENSURE THAT CORRECT RS-232-C PORT IS ENTERED. 
0 CHANGE THE CONTROL CONDITION FOR THE MDR PRINTER REQUIREMENTS 
RELATING TO PAUSE TRANSMISSION CHARACTER, POWER CONTROL AND 
TIMING, OR PRINTOUT FORMAT 
pGGEGG-*I 
1. PLACE PRINTER IN OR OUT OF SERVICE WITH CMC-705: CMC=705 
0 PORT NUMBER (PI) P1:l 
P2:l 
0 IN/OUT OF SERVICE FLAG (P2) 
2. MODIFY PRINTER CONTROLS WITH CMC-901: .I 
0 PORT NUMBER (PI) 
0 PAUSE TRANSMISSION...

RS-232-C Port Configuration Assignkent 
GE awvll sms 
DESCRIPTION 
. ASSIGN OR MODIFY THE CHARACTERISTICS OF THE TWO RS-232-C PORTS 
INCLUDING BIT RATE, PARITY, CHARACTER LENGTH, STOP BIT AND ECHO. 
. BOTH PORTS ARE FULL DUPLEX. 
. DEFAULT STANDARD DATA BASE PRESENTS PORT jif FOR PMP AND PORT 1 FOR 
MDR PRINTER. 
piizGiq 
1. USE CMC-900 TO SET RS-232-C PORT CHARACTERISTICS: 
. PORT (PI) 
. BIT RATE (P2) 
. PARITY (P3) 
l CHARACTER LENGTH (P4) 
. STOP BIT (P5) 
. ECHO BACK (P6) 
NOTE: IF PORT TO BE...

Diagnostic Trunk Connection Assignment 
j-J 
0 CMC-802 DED‘iCATES A TRUNK TO A DESIGNATED STATION FOR AUDITORY, 
RINGING, AND TRANSMISSION VERIFICATION. 
@ AFTER ASSIGNMENT, TESTS CAN BE MADE BY ORIGINATING A CALL TO THE 
TRUNK BY DIALING THE TRUNK ACCESS CODE FOR THE TRUNK GROUP. 
@ WORKING TRUNK CAN BE CONFIRMED BY DIALING AN OUTSIDE DIRECTORY 
NUMBER AND LISTENING FOR CONFIRMATION CALL PROGRESS TONES. 
1 PROCEDURE +[ 
I 
I 
1. USE CMC-802 TO ENTER STATION DIRECTORY NUMBER AND TRUNK 
TO BE TESTED:...

. . . ,.- 
c Measuremen 
DESCRIPTION GE OMNI slxs 
. ASSIGN OR CANCEL TRUNK GROUP NUMBERS TO BE SAMPLED WlTH CMC-600. 
. 
ACTIVATE A TRAFFIC MEASUREMENT STUDY WITH CMC-601. 
@ 
DEFINE THE DISPLAY FOR TRAFFIC MEASUREMENT BASED ON RECENT DATA 
(LESS THAN IO HOURS) OR OLDER DATA (AFTER 10 HOURS). 
. 
TRAFFIC DENSITY PERCENTAGE IS DISPLAYED BASED ON DESIGNATED TRUNK 
GROUP NUMBERS. 
(PROCEDURE1 
CMC=600 
Pl:l 
1. ASSIGN TRUNK GROUP NUMBERS TO BE SAMPLED WITH CMC-600: P2:13 
. REGISTRATION SEQUENCE NUMBER:...

aintenance 
Comman 
Gull 
TRUNK GROUP TRAFFIC 
SCREENING ASSIGNMENT 
TRAFFIC MEASUREMENT 
ACTIVATION 
TRAFFIC MEASUREMENT 
DATA DISPLAY 
TIME AND DATE SETTING 
CIRCUIT BUSY 
ASSIGNMENT 
SMDR IN/OUT OF SERVICE 600 ASSIGNS TRUNK GROUP NUMBERS TO 
TRAFFIC SAMPLE. 
601 ACTIVATES TRAFFIC MEASUREMENT 
STUDY. 
602 DISPLAYS TRAFFIC DENSITY. 
700 
701 
705 SETS SYSTEM HARDWARE AND 
SOFTWARE CLOCK. 
PLACES CIRCUITS IN/OUT OF SERVICE 
FOR MAINTENANCE. 
PLACES SMDR IN/OUT OF SERVICE FOR 
MAINTENANCE. 
3.33  

c-. Maintenance Data Base Commands/ 
CM6 Command Summary (Continued) 
Gull awvn ~Bcs 
0 
0 
e 
e 
0 
e 
0 DEVICE STATUS 800 LISTS FAULTY DEVICES AND LOCATIONS. 
FAULT LOG 
801 
DIAGNOSTIC TRUNK 
CONNECTION 
ASSIGNMENT 
RS-232-C PORT 
CONFIGURATION 
SMDR PRINTER CONTROL 
READ OUT SYSTEM 
SOFTWARE VERSION ID 
DISPLAY 
DISTRIBUTED 
PROCESSOR VERSION ID 
DISPLAY 802 
900 
901 
904 
907 PROVIDES DETAILED FAULT 
INFORMATION FOR TROUBLESHOOTING. 
ASSIGNS A STATION TO A TRUNK FOR 
DIAGNOSTIC VERIFICATION....

Wudent Not 
3.35  

PERFORM THE FOLLOWING PROGRAMMING TASKS IN THE SEQUENCE OUTLINED BELOW AND IN ACCORDANCE 
WITH THE GTE OMNI SBCS MANUAL. COMPLETE THE REVIEW EXERCISE QUESTIONS UPON COMPLETION OF THIS 
LABORATORY ACTIVITY. 
Labo - Maintenance/Data 
WORK ORDER #3.2 
ZOMPANY NAME: NU SYSTEM CO. PHONE #: (703) 555-l 212 
-0CATION: RESTON, VIRGINIA WORK ORDER 3.2 (TASK #l) 
IRIGINATOR: TELECOMMUNICATIONS MANAGER 
TASKS: 0 Set time, day, date with CMC-700. 
0 Take a circuit out of service with CMC-701. 
0 Display software and...

Laboratory Activity - Maintenance/Data 
Base Commands (3.2) (Continued) 
WORK ORDER #3.2 
ZOMPANY NAME: NU SYSTEM CO. PHONE #: (703) 555-1212 
.OCATION: RESTON, VIRGINIA WORK ORDER 3.2 (TASK #2) 
IRIGINATOR: TELECOMMUNICATIONS MANAGER 
rASKS: 
l Restore circuit to service with CMC-701. 
l Display device status with CMC-800. 
l Display fault log with CMC-801. 
(1) Restore the loop tie line to service. (1) Perform maintenance programming commands. 
(2) Unplug one of the CS-10 telephones from its (2)...