GE S5 Service Manual

System installation
19
                                          Document no. M1031517-02
Figure 6 External connections of Compact Monitor frame F-CM(C)1 rev.00...03
(1) Dust filters
(2)  Recorder unit (optional)
(3)  Connector for factory use only
(4) Synchronization connector
(5)  Connector for external keyboard (anesthesia record keeping solution keyboard), K-CREMCO or 
Barcode Reader
(6)  Potential equalization connector
(7)  Serial port connector
(8)  Receptacle for power cord
(9)  NET ID connector...

Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
20
Document no. M1031517-02                                                                           
3.3.2 Connecting to mains
Connect the power cord to the mains power inlet on the side of the power supply unit and to the wall 
socket.
NOTE: Before taking the  monitor into use for the first time, the batteries should be fully charged. Keep 
the monitor connected to the mains until the Battery charging symbol disappears, or in STBY...

System installation
21
                                          Document no. M1031517-02
3.3.5 Inserting the parameter modules
Insert each plug-in parameter module into a module slot. Firmly press the module in position.
NOTE: Ensure that the module is properly oriented (i.e. the module release latch is facing downward).
Do not use two or more modules with identical functions in the monitor.
Modules with identical functions are:
•Hemodynamic multiparameter modules, E-PRESTN, E-PRETN, E-RESTN, M-PRESTN,...

Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
22
Document no. M1031517-02                                                                           
10. Set the monitors network communication according to the network software in use, if 
necessary. Enter the service menu: Monitor Setup -Install/Service (16-4-34) - Service 
(26-23-8)- Frame - Network- Config and set
•Network software S-CNET99 -> DRI Level = 1999
•Network software S-CNET01 -> DRI Level = 2001
•Network software...

System installation
23
                                          Document no. M1031517-02
5. Wait until the normal screen appears and check that a message Field upgrade OK is displayed 
as a note of successful upgrade.
6. Remove the option software card.
7. Enter the service menu and make sure that both options were loaded (Monitor Setup 
-Install/Service  - Service - Frame - Options - Net+DC).
8. Install the device plate for option software on inside the cover for card drive slots. Close the 
cover.
9....

Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
24
Document no. M1031517-02                                                                           
4. Wait until the normal screen appears and check that a message Field Upgrade OK is 
displayed as a note of successful upgrade.
5. Remove the option software card.
6. Switch the monitor to standby.
7. Detach the cover for card drive slots and install the antenna cover.
8. Insert the wireless LAN antenna card into the foremost card...

System installation
25
                                          Document no. M1031517-02
3.4 S/5 Remote Controller, K-CREMCO
To connect S/5 Remote Controller, K-CREMCO, to an S/5 Compact Monitor:
1. Make sure that the monitor is switched to standby.
2. Connect the K-CREMCO to the 5-pin DIN connector X9 that is located on the right side of the 
Compact Monitor display unit.
3.5 Anesthesia Record Keeping Keyboard, K-ARKB
To connect Anesthesia Record Keeping Keyboard, K-ARKB, to an S/5 Compact Monitor:
1....

Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
26
Document no. M1031517-02                                                                           
3.7 S/5 Compact Airway Modules, E-xxxx / M-xxxxx 
This chapter provides information for installing Compact Airway Modules E-xxxxx. 
Figure 9 Compact Airway Module, E-XXXX
Connection to frame
1. Ensure that the module is properly orientated (i.e. module release latch facing downward).
2. Align the module insertion guide slot with the...

System installation
27
                                          Document no. M1031517-02
Scavenging through the ventilator reservoir
Figure 10 Scavenging through ventilator reservoir
1. Connect an exhaust line to the sample gas outlet on the module’s front panel. 
2. Attach the other end of the line to the ventilator reservoir. Make sure that the reservoir tube 
diameter is at least 2 - 3 times larger than the exhaust line. 
Scavenging through the anesthesia gas scavenging system
Anesthesia machines are...

Datex-Ohmeda S/5 Compact Anesthesia and Compact Critical Care Monitors
28
Document no. M1031517-02                                                                           
Connecting directly to the vacuum scavenging system
1. Connect the exhaust line to the monitor’s sample gas outlet.
2. Connect the exhaust line only to an open scavenging system where gas is removed at room 
pressure. Do not connect the monitor directly to a vacuum scavenging system.
Returning sampling gas to the patient circuit 
The...