GE Logiq P5 User Manual

OB-Multigestational
LOGIQ 5 Basic User Manual 9-75
Direction 2300002-100 Rev. 2
Using other OB studies (continued)
 Figure 9-19. OB Touch Panel: ASUM studies
NOTE:  ASUM studies include the following measurements:
•  ASUM: AC, BPD, and CRL
•  ASUM 2001: AC, BPD, CRL, FL, HC, HL, and OFD 

OB/GYN
9-76 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Multiple Fetus
LOGIQ 5 allows you to measure and report multiple fetus 
development. The system can report a maximum of four 
fetuses.
To enter the number of fetuses 
If more than one fetus is imaged during the exam, enter the 
number of fetuses in the Patient Data Entry Menu.
 Figure 9-20. Fetus Number
When you start an OB exam, the system automatically fills in the 
Fetus # field with 1. To change the number:
1.  Move the cursor to the...

OB-Multigestational
LOGIQ 5 Basic User Manual 9-77
Direction 2300002-100 Rev. 2
To identify each fetus
For measurements, calculations, and worksheet displays, the 
system labels each fetus A, B, C, or D. Each fetus is identified 
by a letter and the total number of fetuses. For example, fetus  
A/3 is fetus A from a total of 3.
When scanning, you can enter information about the fetus 
position and placenta location. You can enter the information in 
the Patient Data section of the worksheets and the...

OB/GYN
9-78 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
To view multiple fetuses data on graphs
You can view multiple gestation data on fetal growth curve 
graphs. After you have made measurements for each fetus, 
select Graph Display. 
•  To view the graph for each fetus, do one of the following:
• Adjust the Fetus knob.
•  In the Patient Data section, move the Trackball to 
highlight the FetusNo field. In the list of fetuses, move 
the Trackball to select the fetus you want, and press 
Set....

OB-Multigestational
LOGIQ 5 Basic User Manual 9-79
Direction 2300002-100 Rev. 2
To compare multiple fetus data on a worksheet
With multiple fetuses, you can list and compare measurements 
of the fetuses on the worksheet. 
Select Worksheet Display, then select Fetus Compare. 
 Figure 9-24. OB Worksheet Display Touch Panel 

OB/GYN
9-80 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
To compare multiple fetus data on a worksheet (continued)
When you select Fetus Compare, the system lists the 
measurement results for each fetus on the Worksheet.
 Figure 9-25. Worksheet Display with Fetus Compare 

OB-Multigestational
LOGIQ 5 Basic User Manual 9-81
Direction 2300002-100 Rev. 2
To Show Fetal Trending for Multiple Fetuses 
When you have data for more than one exam, you can show 
fetal trending and compare fetuses on one graph. 
To view fetal trending for multiple fetuses: 
1. Select Graph Display.
2. Select Fetus Compare. 
3. Select Plot Both.
NOTE:  You can only view fetal trending for multiple fetuses in single 
graph display.
 Figure 9-26. Multigestation Fetal Growth Curve Graph
The symbol key for...

OB/GYN
9-82 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
OB Table Editor
You can add user programmable OB tables to the system.
OB Table Settings Menu
You add OB Tables in the Measurement & Analysis menu. To 
open the menu:
1.  On the Touch Panel, select Utility, then select M&A.
2.  Check the Exam Category on the far left of the monitor 
screen.  Make sure that Obstetrics is selected.
If it is not selected, select Obstetrics and continue selecting 
the folders until the appropriate area is...

OB Table Editor
LOGIQ 5 Basic User Manual 9-83
Direction 2300002-100 Rev. 2
OB Table Settings Menu (continued)
3.  On the monitor display, select the OB Table tab.
The system displays the OB Table settings menu. 
 Figure 9-27. OB Table settings 

OB/GYN
9-84 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
OB Table Settings Menu (continued)
4.  The OB Table settings menu lists OB Table parameters. 
Specify the following parameter values as appropriate:
• Study: Shows the study to which this measurement 
table belongs.
• New/Edit: To create a new OB table, select New Table. 
To edit an existing user-programmable OB table, select 
Edit Table.
NOTE:  You cannot edit the system’s OB Tables.
• O B  Ta b l e  Te m p l a t e: To create a new OB...