GE Logiq P5 User Manual

OB Measurements and Calculations
LOGIQ 5 Basic User Manual 9-55
Direction 2300002-100 Rev. 2
Measurement information
This section lists the results of all measurements. 
•  CUA or AUA – If this field is checked, the system uses the 
measurement to calculate the ultrasound age. 
•  Value – The measured value. If more than one 
measurement was made for an item, the system uses the 
specified method (average, maximum, minimum, or last) to 
determine this value.
•  m1–m3 – Up to three measurement values for...

OB/GYN
9-56 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Calculation information
This section of the worksheet provides calculation choices and 
lists calculation results.
•  EFW – lists the parameters used to calculate EFW. This is 
followed by the calculation result. 
To change which parameters are used:
a.  Select this field or press Select EFW.
b.  Select the desired parameters.
•  EFW GP – lists the source used to calculate EFW–GP 
(growth percentile). This is followed by the growth...

Anatomical Survey
LOGIQ 5 Basic User Manual 9-57
Direction 2300002-100 Rev. 2
Anatomical Survey
Overview
The Anatomical Survey page provides a checklist that indicates 
which anatomy was imaged and its appearance.
 Figure 9-7. Anatomical Survey 

OB/GYN
9-58 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Editing
•  To activate the Anatomical Survey, select Anatomy on the 
OB Worksheet Touch Panel.
 Figure 9-8. OB Worksheet Touch Panel
•  Fill the required field.
Table 9-3: Anatomical Survey
FieldDescription
Fetus Pos Indicate the fetal position within the uterus.
PLAC Identify the location of the placenta.
ANATOMY Enter the following information for each part of the 
anatomy imaged:
1. Imaged? : Check the box that you did image this part...

Anatomical Survey
LOGIQ 5 Basic User Manual 9-59
Direction 2300002-100 Rev. 2Select Exit to return to the Scan screen.
Select Worksheet to return to the Worksheet or Graph to enter 
the OB Graph screen on the Touch Panel.
 Figure 9-9. Anatomical Survey Touch Panel
NOTE:  The contents input on the Anatomical Survey page are returned 
to the factory default settings after starting a new patient. 
BIOPHYSICAL The score is _ of 10 possible total points, depending 
upon the number of parameters entered. Enter...

OB/GYN
9-60 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
OB Graphs
Overview
OB Graphs allow you to assess fetal growth compared to a 
normal growth curve. When a patient has completed two or 
more ultrasound exams, you can also use the graphs to look at 
fetal trending. For multi-gestational patients you can plot all 
fetuses and compare the growth on the graphs. 
The LOGIQ 5 provides the following two basic types of graphs:
• Fetal Growth Curve graphs – show one measurement per 
graph. These...

OB Graphs
LOGIQ 5 Basic User Manual 9-61
Direction 2300002-100 Rev. 2
To View OB Graphs
To view OB graphs:
1. Press Measure.
2. Select Graph Display. 
 Figure 9-10. B-Mode OB Measurement Touch Panel 

OB/GYN
9-62 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
To View OB Graphs (continued)
After you select Graph Display, the system displays the OB 
Graph keys on the Touch Panel. 
 Figure 9-11. OB Graph keys on Touch Panel 

OB Graphs
LOGIQ 5 Basic User Manual 9-63
Direction 2300002-100 Rev. 2
To View OB Graphs (continued)
The monitor display shows the Fetal Growth Curve Graph.
 Figure 9-12. Fetal Growth Curve Graph 

OB/GYN
9-64 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Fetal Growth Curve Graph
The horizontal axis shows the fetal age in weeks. The system 
determines this age from the data on the Patient Data Entry 
screen. The vertical axis shows one of the following:
•  For measurements, mm or cm
•  For ratios, percent
•  For fetal weight, grams
The Fetal Growth Curve Graph shows the following information 
for the selected measurement:
•  The normal growth curve
•  The standard deviations or relevant...