GE Logiq 7 Service Manual

GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
Section 3-1 - Overview 3-3
Section 3-2
Receiving and Unpacking the Equipment
When a new system arrives, check that any components are not damaged and are not in short supply. 
If shipping damage or shortage occurs, contact the address shown in Chapter 1.
Unpacking Procedures:
1.) Cut the two Metal Bands.
2.) Lift the Cap up and off.
3.) Remove the six (6) Plastic Joints from the Outer Sleeves.
4.) Remove the Outer Sleeves.
5.) Remove the...

GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
3-4Section 3-1 - Overview
Section 3-2      Receiving and Unpacking the Equipment (cont’d)
NOTE: Check the shipping container for special instructions. Verify that the container is intact. In some  cases a secondary container may be used. If so, ask the carrier for unpacking instructions.
NOTICEFor the protection of LCD monitor, re-use the packing sleeve whenever possible, in case of shipment 
after unpacking.
Figure 3-2 Labels on...

GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
Section 3-1 - Overview 3-5
3-2-1 Safety Reminders
DANGERWHEN USING ANY TEST INSTRUMENT THAT IS CAPABLE OF OPENING THE 
AC GROUND LINE (I.E., METER’S GROUND SWITCH IS OPEN), DO NOT TOUCH 
THE UNIT!
CAUTIONTwo people should unpack the unit because of its weight. Two people are required whenever a 
part weighing 19kg (35 lb.) or more must be lifted.
CAUTIONIf the unit is very cold or hot, do not turn on it s power until it has had a chance...

GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
3-6Section 3-1 - Overview
3-2-2 Moving into Position
In general, a single adult can move the LOGIQ™ 7 along an even surface with no steep grades. At least 
two people should move the machine when large humps, grooves, or grades will be encountered. (It is 
better to pull from the rear rather than push from the front of the unit). Before moving, store all loose 
parts in the unit. Wrap transducers in soft cloth or foam to prevent damage....

GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
Section 3-1 - Overview 3-7
3-2-3 LCD Monitor Tilt Caution
CAUTIONDo NOT put your hand here! Your fingers might be pinched when adjusting angle of the LCD 
monitor.
Figure 3-3   LCD Monitor Tilt Caution
For R7.5.x 19inch LCD system 

GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
3-8Section 3-1 - Overview
3-2-4 LCD Monitor Swing CautionLCD Monitor Tilt Caution
CAUTIONArm can be swung 180 degree left and right, and stick out from the side frame. Pay attention to 
the location from the wall in the room for room layout, and notice the attention to customer for 
Examination Table side.
CAUTIONLCD will hit the KBD in case of moving over the right/left side. 

GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
Section 3-1 - Overview 3-9
3-2-5 LCD Monitor Removal Caution
3-2-6 Shipping Delivery Requirements
Do NOT hold the scanner at the LCD monitor or rotaing arm using the belt as shown. Always hold it at 
the body part of the console.
CAUTIONAlways lock the LCD monitor arm before removing the LCD monitor. This prevents the monitor 
arm from being suddenly and fastly extended when removing the LCD monitor. Failure to heed 
this warning may...

GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
3-10Section 3-3 - Preparing for Installation
Section 3-3
Preparing for Installation
3-3-1 Verify Customer Order
Compare items received by the customer to that which is listed on the delivery order. Report any items 
that are missing, back ordered or damaged.
3-3-2 Physical Inspection
3-3-2-1 System Voltage Settings
• Verify that the scanner is set to the correct voltage. The Voltage settings for the LOGIQ™ 7 Scanner is found on the label...

GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
Section 3-4 - Completing the Installation 3-11
Section 3-4
Completing the Installation
3-4-1 Probe (Transducer) Connection
1.) Connect a transducer to the upper transducer receptacle as follows:
a.) Ensure that the transducer twist lock lever to the horizontal position.
b.) Insert the transducer connector on the receptacle guide pin until it touches the receptacle mating surface.
c.) Twist the transducer twist lock lever to vertical...

GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
3-12Section 3-4 - Completing the Installation
3-4-2 Optional Peripherals/Peripheral Connection
Depending on the customer order, the peripheral(s) already has been installed onto the scanner before 
shipment. If it does not, select the proper location to install the peripherals, following the table below.
Figure 3-5   Optional Peripherals/Peripheral Connection
Location for peripheralOne peripheral 
(Color printer ONLY)One peripheral (VCR...