Fujifilm Camera X100t Owners Manual

							Attaching the Strap
Charging the Battery
Inserting the Battery and a Memory Card
Turning the Camera on and Off
Basic Setup
First Steps
002D0020 003400310020 002D  
						

							Attach the strap clips to the camera and then attach the strap.
Open a strap clip.
Use the clip attaching tool to open a strap clip, making sure that the tool and clip are in
the orientations shown.
Keep the tool in a safe place. You will need it to open the strap clips when
removing the strap.
1. 
Place the strap clip on an eyelet.
Hook the strap eyelet in the clip opening. Remove the tool, using the other hand to keep
the clip in place.2. 
Attaching the Strap
002D0020 003400320020 002D  
						

							Pass the clip through the eyelet.
Rotate the clip fully through the eyelet until it clicks closed.3. 
Attach a protective cover.
Place a protective cover over the eyelet as shown, with the black side of the cover toward
the camera. Repeat Steps 1–4 for the second eyelet.4. 
Insert the strap.
Insert the strap through a protective cover and strap clip.5. 
Attaching the Strap
002D0020 003400330020 002D  
						

							Fasten the strap.
Fasten the strap as shown. Repeat Steps 5–6 for the second eyelet.6. 
To avoid dropping the camera, be sure the strap is correctly secured.
Attaching the Strap
002D0020 003400340020 002D  
						

							The battery is not charged at shipment. Charge the battery before use.
The camera uses an NP-9 5 rechargeable battery.
The battery takes about 4 hours to fully charge.
Place the battery in the charger.
Insert the battery in the orientat ion indicated by the   labels.1. 
Charge lamp
Arrow
 label
Charging the Battery
002D0020 003400350020 002D  
						

							Attach the supplied adapter before charging the battery (the adapter is attached at
shipment).
Adapter
The supplied AC cord is for use exclusiv ely with the supplied battery charger. Do
not use the supplied charger with other co rds or the supplied cord with other
devices.
Plug the charger in.
Plug the charger into an indoor power  outlet. The charging indicator will light.
2. 
Charge the battery.
Remove the battery when charging is complete.3. 
The Charging Indicator
The charging indicato r shows battery charge status as follows:
Charging
indicator Battery status Action
Off Battery not inserted. Insert the battery.
Battery fully
charged.
Remove the battery.
On Battery charging. —
Blinks Battery fault. Unplug the charger and remove the
battery.
Charging the Battery
002D0020 003400360020 002D  
						

							Unplug the charger when it is not in use.
Remove dirt from the battery terminals with a clean, dry cloth. Failure to observe this
precaution could prevent th e battery from charging.
Do not affix stickers or other objects to th e battery. Failure to observe this precaution
could make it impossible to remove the battery from the camera.
Do not short the battery terminal s. The battery could overheat.
Read the cautions in “The Battery and Power Supply”.
Use only battery chargers designated for us e with the battery. Failure to observe this
precaution could result  in product malfunction.
Do not remove the labels from the battery or  attempt to split or peel the outer casing.
The battery gradually loses its charge when not in use. Charge the battery one or two
days before use.
Charging times may increase at very low or very high temperatures.
Charging the Battery
002D0020 003400370020 002D  
						

							Charging via a computer
The battery can be charged by connecting the camera to a computer. Connect the supplied USB
cable as shown, making sure  the connectors are fully inserted.
Connect the camera directly to the comp uter; do not use a USB hub or keyboard.
If the computer goes into sleep mode whil e charging, charging will stop. To continue
charging, disable sleep mode on the comp uter, and disconnect and connect the USB
cable.
Charging may be impossible depending on  computer specifications, settings or
conditions.
The battery status icons show battery charge  status when the camera is turned on, and
the indicator lamp shows it when the camera is turned off.
Battery status icon when
camera on Indicator lamp when
camera off
Battery status
 (yellow) On Battery charging.
 (green) Off Charging
complete.
 (red) Blinks Battery fault.
Charging the Battery
002D0020 003400380020 002D  
						

							Insert the battery and memory card as described below.
Open the battery-chamber cover.
Slide the battery-chamber latch as shown  and open the battery-chamber cover.
Do not open the battery-chamber cover when the camera is on. Failure to observe
this precaution could damage image files or memory cards.
Do not use excessive force when handling the battery-chamber cover.
1. 
Inserting the Battery and a Memory Card
002D0020 003400390020 002D  
						

							Insert the battery.
Using the battery to keep the battery latch pressed to one side, insert the battery
contacts first in the direction shown by the  arrow. Confirm that the battery is securely
latched.
Insert the battery in  the orientation shown.  Do not use force or attempt to
insert the battery upsi de down or backwards.  The battery will slide in easily
in the correct orientation.
2. 
Arrow
Battery latch
Inserting the Battery and a Memory Card
002D0020 003500300020 002D