Fujifilm Camera X100t Owners Manual

							Adjust the appearance of shadows.
[SHADOW TONE]
002D0020 0031003600310020 002D  
						

							Reduce noise in pictures taken at high sensitivities.
[NOISE REDUCTION]
002D0020 0031003600320020 002D  
						

							Select [ON] to reduce mottling in long time-exposures.
[LONG EXPOSURE NR]
002D0020 0031003600330020 002D  
						

							AUTO
Adjust colors to match the light source.Select  [WHITE BALANCE]  in the shooting menu.
1. 
Press the selector up or down to highlight the desired option.
White balance adjusted automatically.
Measure a value for white balance.
Choose a color temperature.
For subjects in direct sunlight.
For subjects in the shade.
Use under “daylight” fluorescent lights.
Use under “warm white” fluorescent lights.
Use under “cool white” fluorescent lights.
Use under incandescent lighting.
Reduces the blue cast typically associated with underwater lighting.2. 
[WHITE BALANCE]
002D0020 0031003600340020 002D  
						

							Press [MENU/OK] . The dialog shown below will be  displayed; use the selector to
fine-tune white balance and press  [MENU/OK] to select, or press  [DISP/BACK] to exit
without fine-tuning.3. 
Results vary with shooting conditions. Play pictures back after shooting to check colors.
Custom White Balance
Color Temperature
Choose   to adjust white balance for unusual lighting conditions. White balance measurement
options will be displayed; frame a white object so  that it fills the display and press the shutter
button all the way down to measure white balance (to select the most recent custom value and
exit without measuring white balance, press  [DISP/BACK], or press [MENU/OK] to select
the most recent value and display the fine-tuning dialog).
If “COMPLETED!” is displayed , press [MENU/OK]  to set white balance to the
measured value.
If “UNDER” is displayed , raise exposure compensation and try again.
If “OVER” is displayed, lower exposure compensation and try again.
[WHITE BALANCE]
002D0020 0031003600350020 002D  
						

							Color temperature is an objective measure of the color of a light source, expressed in Kelvin
(K). Light sources with a color temperature close  to that of direct sunlight appear white; light
sources with a lower color temperature have a yellow or red cast, while those with a higher
color temperature are tinged with blue. You can match color temperature to the light source as
shown in the following table, or choose options that differ sharply from  the color of the light
source to make pictures “warmer” or “colder”.
Choose for redder light sources or “colder” pictures Choose for bluer light sources or “warmer”
pictures
2000  K
Candlelight 5000
 K
Direct sunlight 15000
 K
Blue sky
 Sunset/sunrise Shade  
[WHITE BALANCE]
002D0020 0031003600360020 002D  
						

							Recall settings saved with [EDIT/SAVE CUSTOM SETTING] .
See Also
[EDIT/SAVE CUSTOM SETTING] (Shooting Menu)
[SELECT CUSTOM SETTING]
002D0020 0031003600370020 002D  
						

							Save custom camera settings for commonly-encountered situations.Select  [EDIT/SAVE CUSTOM SETTING]  in the shooting menu.
1. 
Highlight a custom settings bank and press  [MENU/OK] to select.2. 
Adjust the following settings as desired.
To replace the settings in the current bank with the settings currently selected
with the camera, highlight  [SAVE CURRENT SETTINGS] and press  [MENU/OK].
3. 
[ISO]
[DYNAMIC RANGE ]
[FILM SIMULATION]
[WHITE BALANCE]
[COLOR]
[SHARPNESS]
[HIGHLIGHT TONE]
[SHADOW TONE]
[NOISE REDUCTION]
[EDIT/SAVE CUSTOM SETTING]
002D0020 0031003600380020 002D  
						

							Press [DISP/BACK]. A confirmation dialog will be displayed; highlight  [OK] and press
[MENU/OK] .4. 
Settings can be recalled using the  [SELECT CUSTOM SETTING] option in the shooting
menu.
See Also
[SELECT CUSTOM SETTING]  (The Shooting Menu)
[EDIT/SAVE CUSTOM SETTING]
002D0020 0031003600390020 002D  
						

							Choose the roles played by the [Fn] buttons.
Display the shooting menu and select  [FUNCTION (Fn) SETTING].
1. 
Press the selector up or down to highlight the desired button and press  [MENU/OK] to
select. You will be given the following choice of  functions to assign to the selected button.
Select [NONE]  to assign no function to the selected button.
2. 
Highlight the desired function and press  [MENU/OK] to assign it to the selected button.3. 
See Also
The Function Buttons  ([Fn] (Function) Buttons)
[ADVANCED FILTER]
[MULTIPLE EXPOSURE]
[MACRO]
[PREVIEW DEPTH OF FIELD]
[ISO]
[SELF-TIMER]
[IMAGE SIZE]
[IMAGE QUALITY]
[DYNAMIC RANGE]
[FILM SIMULATION]
[WHITE BALANCE]
[ND FILTER]
[PHOTOMETRY]
[AF MODE]
[FOCUS AREA]
[CORRECTED AF FRAME]
[FLASH MODE]
[FLASH COMPENSATION]
[SELECT CUSTOM SETTING]
[MOVIE]
[FACE DETECTION]
[PREVIEW PIC. EFFECT]
[HIGH PERFORMANCE]
[RAW]
[WIRELESS COMMUNICATION]
[CONVERSION LENS]
[SHUTTER TYPE]
[FUNCTION (Fn) SETTING]
002D0020 0031003700300020 002D