Epson Projector BrightLink Pro 1420Wi User Manual

							Parent topic:
Using Finger Touch Interactivity
Calibrating for Finger Touch Interactivity Finger touch calibration coordinates the positioning of your finger with the location of the cursor
(BrightLink Pro 1430Wi).
Note:Make sure you have calibrated the pens before calibrating for finger touch interactivity.
1. Press the Menubutton, select the Extendedmenu, and press Enter.
171 
						

							2. Select the
Easy Interactive Function setting and pressEnter.
3. Select Touch Unit Setup and pressEnter.
4. Select Touch Calibration and pressEnter.
172 
						

							The following screen appears:
5. Adjust the image focus, if necessary.
6. Press Enterto select Yes.
A flashing green circle appears in the upper left corner of your projected image.
7. Touch and hold the center of the circle with your finger until the circle disappears and another circle appears, then release it.
The circle disappears, and you see another circle below the first one.
173  
						

							Note:
For the most accurate calibration, make sure you touch the center of the circle with the tip of
your finger.
Note: Make sure you are not blocking the signal between your finger and the interactive receiver
(next to the projection window on the projector).
8. Touch the center of the next circle with your finger and continue until all of the circles disappear. When you get to the bottom of a column, the next circle appears at the top of a new column.
Note: If you make a mistake, press the Escbutton on the remote control to go back to the previous
circle. To restart the calibration process, press and hold the Escbutton for 2 seconds.
9. If the cursor location and your finger position do not match, repeat these steps to calibrate again.
174  
						

							Parent topic:
Using Finger Touch Interactivity
Related tasks
Adjusting the Angle of the Touch Unit
Using Finger Touch Operations
Using Finger Touch Operations You can use your finger to interact with the projected screen, just as you would use an interactive pen
(BrightLink Pro 1430Wi). You can use either a pen or your finger, or use both at the same time.
When performing touch operations with your finger, you can use two fingers in annotation and
whiteboard modes.
1. Calibrate the pens.
2. Install the Touch Unit as described in your mounts Installation Guide.
3. Adjust the angle of the Touch Unit if it was not adjusted during installation.
4. Calibrate for finger touch interactivity.
5. Turn on your projector. This automatically turns on the Touch Unit also. The blue light on the Touch Unit remains lit.
175  
						

							6. To write or draw on the projection surface in annotation mode or whiteboard mode, do the following:
• To select a projected item, such as an icon, tap the projection surface with your finger.
• To draw on the projected screen, tap the projection surface with your finger and drag it asnecessary.
7. To use your finger as a mouse in PC Interactive mode, do the following:
• To left-click, tap the board with your finger.
• To double-click, tap twice with your finger.
• To right-click, press the board with your finger for about 3 seconds.
• To click and drag, press on and drag an item with your finger.
• To scroll, drag your finger on the screen.
8. If your operating system supports these functions, you can also do the following: • To zoom in or out, touch an item using two fingers and either move your fingers away from eachother (zoom in) or toward each other (zoom out).
• To rotate an image, touch the image with your fingers and rotate your hand.
176   
						

							• To drag up or down on a page, or move backward or forward in a browser window, use swiping
gestures or flicks.
Note: Finger touch operations may not work correctly with long or artificial nails, or fingers wearing
bandages. If your fingers are too close together or crossed, or your sleeve touches the screen, finger
touch may not be recognized. Some operating systems may not support gestures.
Parent topic: Using Finger Touch Interactivity
Related tasks
Calibrating for Finger Touch Interactivity
Using BrightLink With a Computer You can connect a computer to the projector and install the software from the CD labeled Epson
Projector Software for Easy Interactive Function. You can then do the following:
• Use the pens or your finger (BrightLink Pro 1430Wi) as a mouse to control your computer
• Use the Easy Interactive Tools software to annotate with both pens or a combination of pen and fingertouch (BrightLink Pro 1430Wi) at the same time
Note: See the online Easy Interactive Tools Operation Guide for detailed information.
• Save and print your annotations
• Use the Tablet PC input panel in Windows 8.x, Windows 7, or Windows Vista
• Use Ink Tools for annotation in Microsoft Office applications
PC Interactive Mode System Requirements
Switching to PC Interactive Mode
Controlling Computer Features from a Projected Screen (PC Interactive Mode)
Adjusting the Pen Operation Area
Easy Interactive Tools
Windows Pen Input and Ink Tools
Parent topic: Using the Interactive Features
PC Interactive Mode System Requirements Your computer system must meet the system requirements here to use PC Interactive mode and Easy
Interactive Tools.
177 
						

							Note:
Easy Interactive Driver must be installed and running to use Easy Interactive Tools on a Mac.
Requirement Windows Mac
Operating system Windows XP Professional SP2 or later, OS X 10.5.x, 10.6.x, OS X 10.7.x, Home Edition 10.8.x, 10.9.x (32-bit)
OS X 10.6.x, OS X 10.7.x, 10.8.x,
Windows Vista Ultimate, Enterprise,
10.9.x (64-bit)
Business, Home Premium, and Home
Basic (32-bit)
Windows 8.x Pro, Enterprise, Windows 7
Ultimate, Enterprise, Professional, Home
Premium, and Home Basic (32- and 64-
bit)
CPU Intel Pentium M 1.6 GHz or faster (Core2 Power PC G4 1.5 GHz or faster
Duo 1.2 GHz or faster recommended) (Core Duo 1.83 GHz or faster
recommended)
Memory 512MB or more (1G or more recommended)
Hard disk space 100MB or more
Display Resolution between 1024 × 768 and 1920 × 1200, 16-bit color or greater
Parent topic: Using BrightLink With a Computer
Related concepts
Easy Interactive Tools
Switching to PC Interactive Mode You can easily switch between PC Free annotation and PC interactive modes. Although you can use
both pens in PC interactive mode, this may cause interference in some applications that only support
one pen. To avoid interference, turn off the unused pen or move it away from the projection surface.
• To switch to PC interactive mode, select the Pen mode icon on the toolbar, then select theMouse icon.
• To switch back to annotation mode, select the Mouse icon, then select the Pen mode icon.
Parent topic: Using BrightLink With a Computer
178     
						

							Controlling Computer Features from a Projected Screen (PC Interactive Mode)
You can navigate, select, and interact with your computer programs from the projected screen using the
interactive pens or your finger (BrightLink Pro 1430Wi) just as you would a mouse.
Note:OS X users need to install the Easy Interactive Driver before using PC Interactive mode. Go to
epson.com/support (U.S.) orepson.ca/support (Canada) and select your projector.
1. Connect the projector to your computer using a USB cable.
2. Turn on your projector and project your computer screen.
3. Press the Menubutton on the remote control, select the Extendedmenu, and press the Enter
button.
4. Select the USB Type Bsetting and press the Enterbutton.
5. Select one of the following: •Easy Interactive Function to use PC Interactive mode.
• USB Display/Easy Interactive Function to use PC Interactive mode and USB Display.
• Wireless Mouse/USB Display to use the mouse and USB Display
6. Press the Escbutton to exit the USB Type B menu.
179 
						

							7. Select the
Easy Interactive Function setting and press theEnterbutton.
8. Select one of the following as the Pen Operation Modedepending on your projector model and
computer operating system (BrightLink Pro 1430Wi):
BrightLink Pro 1420Wi:
• Two Users/Mouse: Lets you use both interactive pens as a mouse
• One User/Mouse: Lets you use one interactive pen as a mouse
• One User/Pen: Uses the Windows pen and ink feature (Windows 8.x, Windows 7, and Windows
Vista)
BrightLink Pro 1430Wi:
• Mode 1: Windows XP or earlier
• Mode 2: Windows Vista, Windows 7, Windows 8.x, and OS X
• Mode 3: Linux
9. Press the Enterbutton on the remote control and press the Menubutton to exit the Extended menu.
10. Hover near or tap on the board or the projected image with the interactive pen or your finger (BrightLink Pro 1430Wi).
The icon is displayed on the projected screen.
180