Epson Projector BrightLink 585Wi User Manual

							4. Select the
Othersmenu and press Enter.
5. Enter up to two IP addresses to receive SNMP notifications, using 0 to 255 for each address field. Note: Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a
number from 0 to 255).
6. If available, select the Priority Gatewaysetting for your network.
7. If your network environment uses an AMX controller, turn on the AMX Device Discoverysetting to
allow the projector to be detected.
8. If your network environment uses a Crestron RoomView controller, turn on the Crestron RoomView
setting to allow the projector to be detected.
9. If you are connecting to a network using Bonjour, turn on the Bonjoursetting.
10. If you want this projector to receive broadcasted messages over the network, turn on the Message
Broadcasting setting. Administrators can broadcast messages over the network using the Message
Broadcasting plug-in for EasyMP Monitor (Windows only).
11. When you finish selecting settings, select Completeand follow the on-screen instructions to save
your settings and exit the menus.
Parent topic: Using the Projector on a Network
71 
						

							Controlling a Networked Projector Using a Web Browser
Once you have connected your projector to your network, you can select projector settings and control
projection using a compatible web browser. This lets you access the projector remotely.
Note:The web setup and control features support Microsoft Internet Explorer 8.0 or later, and Safari on
networks that do not use a proxy server for connection. You cannot select all of the projector menu
settings or control all projector functions using a web browser.
Note: If you set Standby Mode to Communication On, you can use a web browser to select settings
and control projection even if the projector is in standby mode.
1. Make sure the projector is turned on.
2. Start your web browser on a computer connected to the network.
3. Type the projectors IP address into the browsers address box and press the computers Enterkey.
You see the Web Control screen.
Note: You may need to log in before you see the Web Control screen. If you see a log in window,
enter your user name and password. (The default user name is EPSONWEBand the default
password is admin.)
4. To select projector menu settings, select the name of the menu and follow the on-screen instructions to select settings.
5. To control projection remotely, select the Web Remoteoption.
72 
						

							You see a screen like this:
1 Power button control
2 Selects Computerport source
3 Selects Video,S-Video, and HDMIport sources
4 Freeze button control
5 A/V Mute button control
6 Page Up andPage Down button controls
7 Searches for sources
8 Selects the network source
9 Selects the USB Display or USB device source
10 Volume button controls
11 Closed Caption control
6. Select the icon corresponding to the projector function you want to control.
Parent topic: Using the Projector on a Network
73  
						

							Related references
Projector Setup Settings - Extended Menu
Crestron RoomView Support If you are using the Crestron RoomView network monitoring and control system, you can set up your
projector for use on the system. Crestron RoomView lets you control and monitor your projector using a
web browser.
Note:You cannot use the Epson Web Control feature or the Message Broadcasting plug-in for EasyMP
Monitor when you use Crestron RoomView.
For additional information on Crestron RoomView, contact Crestron.
Setting Up Crestron RoomView Support
Controlling a Networked Projector Using Crestron RoomView
Parent topic: Using the Projector on a Network
Setting Up Crestron RoomView Support To set up your projector for monitoring and control using a Crestron RoomView system, make sure your
computer and projector are connected to the network. If you are connecting wirelessly, set up the
projector using the Advanced network connection mode.
Note:If you want to use the Crestron RoomView system when the projector is turned off, you need to
adjust the Standby Mode settings in the ECO menu.
1. Press the Menubutton.
2. Select the Networkmenu and press Enter.
3. Select Network Configuration and pressEnter.
74 
						

							4. Select the
Othersmenu and press Enter.
5. Set the Crestron RoomView setting toOnto allow the projector to be detected.
Note: Enabling Crestron RoomView disables the Epson Message Broadcast feature in the EasyMP
Monitor software.
6. When you finish selecting settings, select Completeand follow the on-screen instructions to save
your settings and exit the menus.
7. Turn off the projector, then turn it on again to enable the setting.
Parent topic: Crestron RoomView Support
Related references
Projector Setup Settings - Extended Menu
Controlling a Networked Projector Using Crestron RoomView Once you have set up your projector to use Crestron RoomView, you can control and monitor projection
using a compatible web browser.
1. Start your web browser on a computer connected to the network.
2. Type the projectors IP address into the browsers address box and press the computers Enterkey.
75 
						

							You see this screen:
3. Select the input source that you want to control in the Sources List box. You can scroll through available sources using the up and down arrows in the box.
4. To control projection remotely, click the on-screen buttons that correspond to the projectors remote control buttons. You can scroll through button options at the bottom of the screen.
Note: These on-screen buttons do not directly correspond to the projectors remote control buttons:
• OK acts as the Enterbutton
• Menu displays the projectors menu
5. To view information about the projector, click the Infotab.
6. To change projector, Crestron, and password settings, click the Toolstab, select settings on the
displayed screen, and click Send.
7. When you finish selecting settings, click Exitto exit the program.
Parent topic: Crestron RoomView Support
76  
						

							Using Basic Projector Features
Follow the instructions in these sections to use your projectors basic features.
Turning On the Projector
Turning Off the Projector
Selecting the Language for the Projector Menus
Image Shape
Resizing the Image with the Wide and Tele Buttons
Adjusting the Image Position
Focusing the Image
Remote Control Operation
Selecting an Image Source
Projection Modes
Image Aspect Ratio
Color Mode
Controlling the Volume with the Volume Buttons
Projecting a PC Free Presentation
Turning On the Projector Turn on the computer or video equipment you want to use before you turn on the projector so it can
display the image source.
77 
						

							1. Connect the power cord to the projectors power inlet.
2. Plug the power cord into an electrical outlet.
Note: WithDirect Power On turned on, the projector turns on as soon as you plug it in.
The projectors power light turns blue. This indicates that the projector is receiving power.
3. Press the power button on the projector or the remote control to turn on the projector. The projector beeps and the Status light flashes blue as the projector warms up. Once the projector
is warmed up, the Status light stops flashing and turns blue.
Warning: Never look into the projector lens when the lamp is on. This can damage your eyes and is
especially dangerous for children.
78  
						

							If you do not see a projected image right away, try the following:
• Turn on the connected computer or video device.
• Press the
Source Search button on the projector or remote control to detect the video source.
• Press the button for the video source on the remote control.
Parent topic: Using Basic Projector Features
Turning Off the Projector Before turning off the projector, shut down any computer connected to it so you can see the computer
display during shutdown.
Note:Turn off this product when not in use to prolong the life of the projector. Lamp life will vary
depending upon mode selected, environmental conditions, and usage. Brightness decreases over time.
Note: When using the A/V Mute feature, the projector lamp is still on. To turn off the lamp, turn off the
projector.
1. Press the power button on the projector or the remote control.
The projector displays a shutdown confirmation screen.
2. Press the power button again. (To leave it on, press any other button.) The projector beeps twice, the lamp turns off, and the Status light turns off.
Note: With Epsons Instant Off technology, there is no cool-down period so you can pack up the
projector for transport right away (if necessary).
79 
						

							3. To transport or store the projector, make sure the Status light is off, then unplug the power cord.
Caution: To avoid damaging the projector or lamp, never unplug the power cord when the Status
light is on or flashing.
4. Parent topic: Using Basic Projector Features
Related references
Projector Setup Settings - Extended Menu
Selecting the Language for the Projector Menus If you want to view the projectors menus and messages in another language, you can change the
Language setting.
1. Turn on the projector.
2. Press theMenubutton.
80